To Order:
Call 800-585-1285
Monday to Friday 9 to 6 EST
Saturday 10 to 5 EST
Sunday Closed
or
E-mail [email protected]

Se habla Español
We speak English,
Russian & Hebrew

Home
Product Site Map
Brand Site Map
Style Site Map
CLEARANCE

Call Brand Lighting Sales 800-585-1285
Ask about SALES & SPECIALS!
Ask about FREE SHIPPING*!
(where available)

Search Brand Lighting Website:

Bruck Lighting System LEDRA

Compare Step Lights & Wall Lights...>
Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>
Compare Brick Lights & Paver Lights...>

Bruck Lighting Ledra AL-J LED Exterior Lights

Bruck Lighting Ledra AL-J LED Step Lights

Bruck Lighting LEDRA AL-C

Click to email for pricing. Bruck Lighting LEDRA™ AL-C

Ask about FREE SHIPPING*
& Additional Discounts on Bruck Lighting

The Bruck LEDRA AL-C hard anodized aluminum housing and decorative collar with 3/8" thick tempered borosilicate glass dome. Provided with an integral driver enclosed in the housing. The LEDRA AL-C attaches is an ideal decorative light point especially for difficult to access locations. Suitable for wet locations.

Technical Specs:
100-240V AC, 50/60Hz input
700mA DC constant current output
6VA, 3W for 1 (3 Watt LED )
White source of 140 lumens
Warm White source of 120 lumens

Listed for wet locations
Short circuit protection
Overload protection
Thermal protection

Part Numbers:

Important Safety Instructions

  1. THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED, IN ACCORDANCE WITH LOCAL NEC CODE.
  2. WET LOCATION SUITable.
  3. SUITable FOR SUSPENDED CEILING
  4. When mounting onto uneven surfaces, silicone must be applied inbetween the canopy housing and the surface to prevent water infiltration.
  5. Turn off power prior to any work on the systems.
  6. Warranty is void in case of unauthorized modifications and/ or improper use.
  7. Must be attached to a 1/2" NPT conduit fitting.
  8. Not thru-wire rated.

Warranty:
All 3 Watt LED fixtures are warranted to be free from defects in material and workmanship for three (3) years from date of delivery.
For full warranty details, visit http: //www.brucklightingsystems.com/contacts/conditions_of_sales/
(Site will open in a new window.)

135331-1mc/f LEDRA® AL-C  Matte Chrome, Frosted Warm White $255.00
135331mc/f LEDRA® AL-C  Matte Chrome, Frosted White $255.00
135332mc/f LEDRA® AL-C  Matte Chrome, Blue $255.00
135333mc/f LEDRA® AL-C  Matte Chrome, Green $255.00
135334mc/f LEDRA® AL-C  Matte Chrome, Red $255.00
135335mc/f LEDRA® AL-C  Matte Chrome, Amber $255.00
135341-1mc/f LEDRA® AL-J Matte Chrome, Frosted Warm White $251.25
135341mc/f LEDRA® AL-J Matte Chrome, Frosted White $251.25
135342mc/f LEDRA® AL-J Matte Chrome, Blue $251.25
135343mc/f LEDRA® AL-J Matte Chrome, Green $251.25
135344mc/f LEDRA® AL-J Matte Chrome, Red $251.25
135345mc/f LEDRA® AL-J Matte Chrome, Amber $251.25

READ ALL OF THESE Installation: INSTRUCTIONS BEFORE INSTALLING THE FIXTURE

Installation: Instructions

Step 1

  • Drill a 1 5/8" hole into the mounting surface.

Step 2

  • Unscrew the set screw (B) from the AL-C cover (A) and unscrew the cover from the base (G).
  • Remove the retaining ring (C) from the base with a needle nosed pliers and lift up the LED plate (D) with the LED driver attached.
  • Place the rubber gasket (H) at the bottom of the product.
  • Pull the wires (I) from the conduit into the wiring compartment in the AL-C.

Step 3

  • Align the base with the rubber gasket (H) so that the mounting screws (E) will go through. Screw the base (G) to the mounting surface.
    (Important: The rubber gasket (H) must be used at the bottom of the product before it is secured to the mounting base).

Step 4

  • Connect the white, black and ground wires from the conduit to the wires from the AL-C using UL listed wire nuts.
  • Green wire should be grounded in accordance with local electrical codes.
  • The wire connections should be made in the wiring compartment.

Step 5

  • Push the LED (D) and the LED driver back into the fixture and replace the retaining ring (C) in the fixture.

Step 6

  • Screw the AL-C cover (A) securely onto the base (G) and tighten the set screw (B) to complete the Installation.