Hadco Path Lights - Beacons

Hadco DW1 Cast Brass Line Voltage Beacon Path Light

Housing: Die cast brass upper housing. Single-piece compression molded fiberglass reinforced polyester composite lower housing. gasketing is silicone. Fasteners are 300 series stainless steel. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.
Finish: Natural Brass (N) is as-cast and tumble polished. Composite is pressure formed, molded-in color.
OPTICAL ASSEMblY: Frosted borosilicate glass.
Lamping: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 120VAC, 60Hz input to step-down transformer. 12VAC output to fixture, for use with low voltage lamps. Fixture is pre-wired with 18 AWG Black, white, and ground wires.
WARRANTY: Lifetime limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 8 3/16" (224mm)
Width: 4 15/16" (126mm)

Hadco DWL1 Cast Brass Low Voltage Beacon Path Light

Housing: Die cast brass upper housing. Single-piece compression molded fiberglass reinforced polyester composite lower housing. gasketing is silicone. Fasteners are 300 series stainless steel. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.
Finish: Natural Brass (N) is as-cast and tumble polished. Composite is pressure formed, molded-in color.
OPTICAL ASSEMblY: Frosted borosilicate glass.
Lamping: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 120VAC, 60Hz input to step-down transformer. 12VAC output to fixture, for use with low voltage lamps. Fixture is pre-wired with 18 AWG Black, white, and ground wires.
WARRANTY: Lifetime limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 8 3/16" (224mm)
Width: 4 15/16" (126mm)

Hadco DWC1 Line Voltage Fiberglass Beacon

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Single-piece molded silicone gasket to prevent water, dust, and insect filtration. Fasteners are 300 series stainless steel. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Frosted borosilicate glass.
Lamping: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 120VAC, 60Hz input to step-down transformer. 12VAC output to fixture, for use with low voltage lamps. Fixture is pre-wired with 18 AWG Black, white, and ground wires.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 8 3/16" (224mm)
Width: 4 15/16" (126mm)

Hadco DWCL1 Low Voltage Fiberglass Beacon

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Single-piece molded silicone gasket to prevent water, dust, and insect filtration. Fasteners are 300 series stainless steel. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Frosted borosilicate glass.
Lamping: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 8 3/4" (222mm)
Width: 5" (127mm)

Hadco DWC2 Line Voltage Fiberglass Beacon

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. gasketing is silicone. Fasteners are 300 series stainless steel. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Ribbed clear acrylic.
Lamping: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. Fixture is 12 volt. Internal electronic transformer has 120 volt input. Pre-wired with high temperature 18 AWG wire.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 7 3/8" (188mm)
Width: 5 5/16" (135mm)

Hadco DWCL2 Low Voltage Fiberglass Beacon

Housing: Fasteners are 300 series stainless steel. gasketing is silicone. Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Two (2) 1/2" conduit inlets at bottom. Note: Watertight connectors and potting compound (by others) must be used to maintain a watertight seal at conduit entry points.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Ribbed clear acrylic. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
Lamping: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 7 3/8" (188mm)
Width: 5 5/16" (135mm)

Hadco 1010 Aluminum Beacon Path Light

Housing: Die-cast aluminum. Removable roof for easy relamping. Fasteners are 300 series stainless steel. Molded silicone gasket seals glass, top and bottom, and prevents moisture intrusion into the fixture. NOTE: The base has two (2) 1/2" NPT conduit entrances for connection to the power source.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.
OPTICAL ASSEMblY: Clear borosilicate glass refractor lens. Fully gasketed top and bottom.
Lamping: 13W CFL (GX23D-2). 50W HPS medium base E17 lamp. 75W MV medium base E17 lamp. 100W maximum A19 lamp. Electrical Assembly: Incandescent is medium base porcelain socket with nickel-plated screw shell and center contact. 13W Fluorescent Socket is a GX23/GX23-2. HID is 4kv rated medium base porcelain socket with nickel-plated screw shell and center contact.
BALLAST: All HID ballasts are core and coil and regulated with power factors better than 90% (HPF). Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation. Ballasts are factory pre-wired and tested. Metal halide ballasts are capable of starting at -20° F or -30° C and HPS at -40°F or -40°C. NOTE: All ballasts are EISA / Title 20 / Title 24 compliant where applicable. Fluorescent ballast is core and coil, NPF Class B. Fluorescent ballast is capable of starting at 0° F or -18° C. Ballast is factory wired and tested.
Installation: & Mounting: VOLTAGE CAUTION: Some local interpretation of the NEC Section 210-6 only permit the use of 120 volt fixtures when they are mounted below 8'. Check with local authorities before specifying alternate voltages. Beacons are partially recessed. Potting compound must be used to seal the conduit wire entry. Lower housing may be recessed directly in the ground or in concrete.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 9 1/32" (229mm)
Width: 8 3/8" (213mm)

Hadco 1012 Aluminum Beacon Path Light

Housing: One-piece injection molded polyester resin. Removable roof for easy relamping. Fasteners are 300 series stainless steel. Molded silicone gasket seals glass, top and bottom, and prevents moisture intrusion into the fixture. NOTE: The base has two (2) 1/2" NPT conduit entrances for connection to the power source.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Clear borosilicate glass refractor lens. Fully gasketed top and bottom.
Lamping: 13W CFL (GX23D-2). 50W HPS medium base E17 lamp. 75W MV medium base E17 lamp. 100W maximum A19 lamp. Electrical Assembly: Incandescent is medium base porcelain socket with nickel-plated screw shell and center contact. 13W Fluorescent socket is a GX23/GX23-2. HID is 4kv rated medium base porcelain socket with nickel-plated screw shell and center contact.
BALLAST: All HID ballasts are core and coil and regulated with power factors better than 90% (HPF). Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation. Ballasts are factory pre-wired and tested. Metal halide ballasts are capable of starting at -20° F or -30° C and HPS at -40°F or -40°C. NOTE: All ballasts are EISA / Title 20 / Title 24 compliant where applicable. Fluorescent ballast is core and coil, NPF Class B. Fluorescent ballast is capable of starting at 0° F or -18° C. Ballast is factory wired and tested.
Installation: & Mounting: VOLTAGE CAUTION: Some local interpretation of the NEC Section 210-6 only permit the use of 120 volt fixtures when they are mounted below 8'. Check with local authorities before specifying alternate voltages. Beacons are partially recessed. Potting compound must be used to seal the conduit wire entry. Lower housing may be recessed directly in the ground or in concrete.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 12 1/4" (311mm)
Width: 8 3/8" (213mm)

Hadco 1019 Aluminum Beacon Path Light

Housing: Natural cast bronze. Removable roof for easy relamping. Fasteners are 300 series stainless steel. Molded silicone gasket seals glass, top and bottom, and prevents moisture intrusion into the fixture. NOTE: The base has two (2) 1/2" NPT conduit entrances for connection to the power source.
Finish: Natural Bronze (N) is as-cast, will age over time.
OPTICAL ASSEMblY: Clear borosilicate glass refractor lens. Fully gasketed top and bottom.
Lamping: 13W CFL (GX23D-2). 75W MV medium base E17 lamp. 100W maximum A19 lamp.
BALLAST: All HID ballasts are core and coil and regulated with power factors better than 90% (HPF). Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation. Ballasts are factory pre-wired and tested. Metal halide ballasts are capable of starting at -20° F or -30° C and HPS at -40°F or -40°C. NOTE: All ballasts are EISA / Title 20 / Title 24 compliant where applicable. Fluorescent ballast is core and coil, NPF Class B. Fluorescent ballast is capable of starting at 0° F or -18° C. Ballast is factory wired and tested.
Installation: & Mounting: VOLTAGE CAUTION: Some local interpretation of the NEC Section 210-6 only permit the use of 120 volt fixtures when they are mounted below 8'. Check with local authorities before specifying alternate voltages. Lower housing may be recessed directly in the ground or in concrete. Beacons are partially recessed. Potting compound must be used to seal the conduit wire entry.
WARRANTY: Lifetime limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 9 1/32" (229mm)
Width: 8 3/8" (213mm)

Hadco RB711 Line Voltage Beacon

Finish

• (A) Black
• (B) White
• (G) Verde
• (H) Bronze
• (J) Green
• Custom Colors Available

Housing: Die-cast zinc. Removable head . Easy access to lamp. Single-piece compression molded fiberglass reinforced polyester composite lower housing. A weatherproof ballast assembly isolates the ballast from water and heat for longer life. All non-ferrous fasteners prevent corrosion and ensure longer life.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications. For larger projects where a custom color is required, contact the factory for more information.
OPTICAL ASSEMblY: Asymmetric. Cylindrical tempered glass refractor lens. Integral shield limits light distribution to a 180° pattern.
Lamping: Incandescent Medium Base A19. 26W CFL (GX24Q-3). 32W CFL (GX24Q-3). 42W CFL (GX24Q-4). MH and HPS Medium base: E17. 70W maximum T6 MH. Lamp is not included. Electrical Assembly: Key-slotted Ballast Assembly with Quick Disconnects mounted to cast aluminum bracket for easy maintenance. 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. 26W Fluorescent socket is a GX24Q-3 base. 32W Fluorescent socket is a GX24Q-3 base. 42W Fluorescent socket is a GX24Q-4 base. Bi-pin socket type (G12) for T6 lamps, with 250° Celsius high temperature teflon coated wire leads.
BALLAST: T6 Metal Halide lamp uses an electronic ballast. All other HID ballasts are core and coil. Ballasts are factory pre-wired and tested, and mounted to a removable tray with quick-disconnect for easy Installation: . Fluorescent ballast is electronic. Ballast is capable of starting at 0° F or -18° C. Ballast is factory wired and tested.
Installation: & Mounting: Lower housing may be recessed directly in the ground or in concrete.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: Above Grade: 5 1/4" (13cm)
Height: Below Grade: 7 1/2" (19cm)
Width: 6 11/16" (17cm)

Hadco RL721 Line Voltage Beacon

Finish

• (A) Black
• (B) White
• (G) Verde
• (H) Bronze
• (J) Green
• Custom Colors Available

Housing: Die-cast zinc. Removable head . Easy access to lamp. Single-piece compression molded fiberglass reinforced polyester composite lower housing. A weatherproof ballast assembly isolates the ballast from water and heat for longer life. All non-ferrous fasteners prevent corrosion and ensure longer life.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications. For larger projects where a custom color is required, contact the factory for more information.
OPTICAL ASSEMblY: Asymmetric. Cylindrical tempered glass refractor lens. Integral shield limits light distribution to a 180° pattern.
Lamping: Incandescent Medium Base A19. 26W CFL (GX24Q-3). 32W CFL (GX24Q-3). 42W CFL (GX24Q-4). MH and HPS Medium base: E17. 70W maximum T6 MH. Lamp is not included. Electrical Assembly: Key-slotted Ballast Assembly with Quick Disconnects mounted to cast aluminum bracket for easy maintenance. 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. 26W Fluorescent socket is a GX24Q-3 base. 32W Fluorescent socket is a GX24Q-3 base. 42W Fluorescent socket is a GX24Q-4 base. Bi-pin socket type (G12) for T6 lamps, with 250° Celsius high temperature teflon coated wire leads.
BALLAST: T6 Metal Halide lamp uses an electronic ballast. All other HID ballasts are core and coil. Ballasts are factory pre-wired and tested, and mounted to a removable tray with quick-disconnect for easy Installation: . Fluorescent ballast is electronic. Ballast is capable of starting at 0° F or -18° C. Ballast is factory wired and tested.
Installation: & Mounting: Lower housing may be recessed directly in the ground or in concrete.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: Above Grade: 5 1/4" (13cm)
Height: Below Grade: 7 1/2" (19cm)
Width: 6 11/16" (17cm)

Hadco RR701 Line Voltage Beacon

Finish

• (A) Black
• (B) White
• (G) Verde
• (H) Bronze
• (J) Green
• Custom Colors Available

Housing: Die-cast aluminum. Removable head . Easy access to lamp. Single-piece compression molded fiberglass reinforced polyester composite lower housing. A weatherproof ballast assembly isolates the ballast from water and heat for longer life. All non-ferrous fasteners prevent corrosion and ensure longer life.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications. For larger projects where a custom color is required, contact the factory for more information.
OPTICAL ASSEMblY: Symmetric. Die-cast zinc vertical louvers with tempered glass refractor bowl.
Lamping: Lamp is not included. 70W maximum T6 MH. MH and HPS Medium base: E17. Incandescent Medium Base A19. 26W CFL (GX24Q-3). 32W CFL (GX24Q-3). 42W CFL (GX24Q-4). Electrical Assembly: Key-slotted Ballast Assembly with Quick Disconnects mounted to cast aluminum bracket for easy maintenance. Bi-pin socket type (G12) for T6 lamps, with 250° Celsius high temperature teflon coated wire leads. 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. 26W Fluorescent socket is a GX24Q-3 base. 32W Fluorescent socket is a GX24Q-3 base. 42W Fluorescent socket is a GX24Q-4 base.
BALLAST: T6 Metal Halide lamp uses an electronic ballast. All other HID ballasts are core and coil. Ballasts are factory pre-wired and tested, and mounted to a removable tray with quick-disconnect for easy Installation: . Fluorescent ballast is electronic. Ballast is capable of starting at 0° F or -18° C. Ballast is factory wired and tested.
Installation: & Mounting: Lower housing may be recessed directly in the ground or in concrete.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: Above Grade: 5 1/4" (13cm)
Height: Below Grade: 7 1/2" (19cm)
Width: 6 11/16" (17cm)