Hadco BrickLytes - Brick Lights & LED Brick Lights

Hadco Low Voltage, Line Voltage & LED Polycarbonate BrickLytes

Housing: Die-cast aluminum faceplate with galvanized steel, single gang recessed box with stainless steel fasteners. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Gasketing is silicone. Fasteners are 300 series stainless steel. Note: Recessed housing contains four (4) ½" NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications. Zinc-rich primer and thermoset powdercoat for durability.
12 Volt Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is pre-wired with 6-ft. pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.
Finish: A Black, H Bronze
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG Black, white, and ground wires.
WARRANTY: Three-year limited warranty.
LED WARRANTY: Five-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards. ADA Compliant when used in indoor and outdoor wall applications.
ADA Compliant – Compliant when used in indoor and outdoor wall applications. ETL, cETL Listed.

Compare Brick Lights & Paver Lights...>

120 Volt RSS2, RSS2 LED Polycarbonate
OPTICAL ASSEMblY: Specular aluminum formed reflector. Clear UV stabilized injection molded polycarbonate with 45 degree louvered screen insert.
Lamping: 18W CFL (G24Q-2). 13W CFL (GX23D-2). 40W maximum T10 (4KV medium base porcelain socket). Lower wattage lamps are acceptable.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. 18W Fluorescent is a GX24q-2 socket.
LED Electrical Assembly: Pre-wired with high temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40ºC/F minimum starting temperature.

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

12 Volt RSBL2, 120 Volt RSB2 Polycarbonate

Compare Brick Lights & Paver Lights...>

12 Volt RSFL2, 120 Volt RSF2, RSF2 LED Polycarbonate

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

Hadco Louver BrickLytes

Housing: Aluminum parts have zinc-rich primer and thermoset powdercoat for durability. Faceplates are color-impregnated. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Die-cast aluminum trim contains less than 0.3% copper to resist corrosion. Thermal Protection device is required for installations in drywall, plaster, wood or other non-masonry materials.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Zinc-rich primer and thermoset powdercoat for durability.
OPTICAL ASSEMblY: The cast louver offers lower light levels with cut-off for lighting stairways or general lighting where shielding of the light source is more important than high light levels.  Symmetric reflector is precision formed, steel with a white reflective coating. Horizontal louver lens made of die-cast copper-free aluminum with a 45° cutoff and frosted tempered glass. Cast bronze louver is natural cast bronze with frosted tempered glass.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards. ADA Compliant when used in indoor and outdoor wall applications.
ADA Compliant – Compliant when used in indoor and outdoor wall applications. ETL, cETL Listed.

Compare Brick Lights & Paver Lights...>

12 Volt RSCL2, 120 Volt RSC2, RSC2 LED Aluminum

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

12 Volt RSCL2, 120 Volt RSC2, RSC2 LED Natural Brass
Finish: N Natural Brass
Natural Brass louver is Natural Brass with frosted tempered glass.
120 Volt Lamping: 9W PLS Fluorescent (G23). 13W PLC Fluorescent (120V: GX23-2; 277V: G24Q-1). 18W CFL (G24Q-2). Two 18W maximum S-8 (1141) lamps (Single contact bayonet base). 40W maximum T10 (4KV medium base porcelain socket). Lower wattage lamps are acceptable.
12 Volt Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is pre-wired with 6-ft. pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG Black, white, and ground wires. 1141 lamps use an integral 120V/12V transformer.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal).
LED Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40ºC/F minimum starting temperature. Pre-wired with high temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs.

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

12 Volt RSVL2, 120 Volt RSV2, RSV2 LED Aluminum

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

12 Volt RSVL2, 120 Volt RSV2, RSV2 LED Natural Brass

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.