Hadco I2/I2G - Small Incandescent Line Voltage Inground Landscape Light

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Trim ring is a die-cast stainless steel. Trim ring is natural cast bronze. Rock guard used for directional glare control made of compression molded polyester.
Finish: Composite is textured, pressure formed, molded-in-color.
H Bronze
N Natural Brass
SS Stainless steel (Matte Finish)
OPTICAL ASSEMblY: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens.
Lamping: 100W maximum PAR30/R30 medium base lamp. 100W maximum PAR20/R20 medium base lamp. Lamp is not included. Lower wattage lamps are acceptable. (Note: PAR20/R20 and PAR30/R30 are not aimable.). Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when flush mounted with CP2 or CPS2.
Height: 8 13/16" (224mm)
Width: 6 5/8" (169mm)

Hadco I2.5 LED Inground Landscape Light

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood

LED (Light Emitting Diode) Included
Smart select driver: 120-277 vac 50/60 Hz auto-sensing

Description
The revolutionary i2.5 composite inground provides optimum performance in a small aperture luminaire. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i2.5 reinforces HADCO's position as the leader in landscape lighting. Now available with LED!

Housing: Separate sealed compartments provide isolation between field wiring, optics, and ballast (CFL). Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match trim ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted, silicone- gasket cover. Rock guard made of cast brass (natural finish) or cast stainless steel (satin finish). Ring is factory pre-drilled for optional guard. Trim ring is natural cast bronze or cast stainless steel. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Half dome 360 degree field adjustable for glare control, constructed of natural cast brass (natural finish) or cast stainless steel (satin finish) to match lens ring. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.
Finish: Natural Brass has satin matte finish. Stainless Steel has satin matte finish.
Lamping: 5,000K color temperature (CCT) or 3,000K amber coated tempered glass lens. Approximately 50,000 hours of operational life (at 25 C ambient temperature and 70% lumen maintenance). >80 CRI.
OPTICAL ASSEMblY: Clear, flat, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded 100% silicone gasket, factory adheared. Optional lens assemblies include cool touch lens, reducing lens temperatures by 35%, ice blue lens, linear or multi-directional spread lens. Sealed optical chamber. Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less LOC-AIM^®. Handle enables easy tool-less removal of optical assembly for hot aiming and re-lamping, simply press-fit back into place. Electrical Assembly: Smart Select Electronic Driver 120 to277 VAC input; 50-60Hz; auto-sensing. Operating start temperature -40 C (-40 F) 17watts consumed (total fixture consumption)
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA compliant when used in concrete and flush mounted with CPS25.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).

Hadco I2.5 HID Inground Landscape Light

• (SP ) Spot
• (NF ) Narrow Flood
• (FL ) Flood
• (0) No Refl. Lamps

Description
The revolutionary i2.5 composite inground provides optimum performance in a small aperture luminaire. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i2.5 reinforces HADCO's position as the leader in landscape lighting.

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Separate sealed compartments provide isolation between field wiring, optics, and ballast (MH and CFL). Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match trim ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted, silicone- gasket cover. Rock guard made of cast brass (natural finish) or cast stainless steel (satin finish). Ring is factory pre-drilled for optional guard. Trim ring is natural cast bronze or cast stainless steel. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Half dome 360 degree field adjustable for glare control, constructed of natural cast brass (natural finish) or cast stainless steel (satin finish) to match lens ring. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.
Finish: Composite is pressure formed, molded-in color. Natural Brass has satin matte finish. Stainless Steel has satin matte finish.
OPTICAL ASSEMblY: Clear, flat, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded 100% silicone gasket, factory adheared. Optional lens assemblies include cool touch lens, reducing lens temperatures by 35%, ice blue lens, linear or multi-directional spread lens. Sealed optical chamber. Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less LOC-AIM^®. Handle enables easy tool-less removal of optical assembly for hot aiming and re-lamping, simply press-fit back into place. High performance aluminum reflector for optimum symmetrical light output. Reflectors for T4 and T6 available for spot, narrow flood, or flood beam pattern. Reflectors for E17 available for spot or flood beam pattern.
Lamping: 70W maximum MH G8.5 base: T4. 70W maximum MH G12 base: T6. 70W maximum MH Medium base: E17. 70W maximum MH Medium base: PAR/R 20/30. Lamp is not included. See Ordering Guide for specific lamp types and wattages available. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. Key-slotted Ballast Assembly with Quick Disconnects mounted to cast aluminum bracket for easy maintenance. Bi-pin socket type (G8.5) with 250° Celsius high temperature teflon coated wire leads. Bi-pin socket type (G12) for T6 lamps, with 250° Celsius high temperature teflon coated wire leads.
BALLAST: All metal halide HID ballasts are Smart Select™ universal electronic that automatically detect 120-277 volts, 50/60 Hz and are regulated with power factors better than 90% (HPF). Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation, sound rated "A", thermally protected, internally fused, output is short circuit protected, no PCBs. Ballasts are factory pre-wired and tested. Metal Halide ballasts are capable of starting at -20° F or -30° C. 50W MH ballasts are capable of starting at 5° F or -15° C.
CERTIFICATIONS: Manufactured to ISO 9001:2000 Standards. ADA compliant when used in concrete and flush mounted with CPS25. ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).
Height: 15 3/4
Width: 7 1/2
Depth: 9 3/4

Hadco I2.5 Fluorescent Inground Landscape Light

Description
The revolutionary i2.5 composite inground provides optimum performance in a small aperture luminaire. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i2.5 reinforces HADCO's position as the leader in landscape lighting.

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Separate sealed compartments provide isolation between field wiring, optics, and ballast (MH and CFL). Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match trim ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted, silicone- gasket cover. Rock guard made of cast brass (natural finish) or cast stainless steel (satin finish). Ring is factory pre-drilled for optional guard. Trim ring is natural cast bronze or cast stainless steel. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Half dome 360 degree field adjustable for glare control, constructed of natural cast brass (natural finish) or cast stainless steel (satin finish) to match lens ring. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.
Finish: Composite is pressure formed, molded-in color. Natural Brass has satin matte finish. Stainless Steel has satin matte finish.
OPTICAL ASSEMblY: Clear, flat, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded 100% silicone gasket, factory adheared. Optional lens assemblies include cool touch lens, reducing lens temperatures by 35%, ice blue lens, linear or multi-directional spread lens. Sealed optical chamber. Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less LOC-AIM^®. Handle enables easy tool-less removal of optical assembly for hot aiming and re-lamping, simply press-fit back into place. High performance aluminum reflector for optimum symmetrical light output. Reflectors for CFL are flood beam pattern.
Lamping: 26W CFL (GX24Q-3). 32W CFL (GX24Q-3). 42W CFL (GX24Q-4). Lamp is not included. Electrical Assembly: 42W Fluorescent socket is a GX24Q-4 base. (Will also accept 26W and 32W PLT lamps). Key-slotted Ballast Assembly with Quick Disconnects mounted to cast aluminum bracket for easy maintenance.
BALLAST: All fluorescent ballasts are Smart Select™ universal electronic that automatically detect 120-277 volts, 50/60 Hz and are regulated with power factors better than 90% (HPF). Ballast provides +/- 5% lamp power regulation with +/- 10% input voltage regulation, sound rated "A", thermally protected, internally fused, output is short circuit protected, no PCBs. Ballast is factory pre-wired and tested. Ballast is capable of starting at 0° F or -18° C.
CERTIFICATIONS: Manufactured to ISO 9001:2000 Standards. ADA compliant when used in concrete and flush mounted with CPS25. ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).
Height: 15 3/4
Width: 7 1/2
Depth: 9 3/4

LED Accessory Adaptor Ring

Internal Accessory Adaptor, attaches to LED board

External Cast Natural Bronze Rock Guard

Cast Rock Guard - Natural Cast Bronze

External Cast Stainless Steel Rock Guard

Cast Rock Guard - Stainless Steel

External Cast Natural Bronze` Half Dome

Half Dome - Natural Cast Bronze

External Cast Stainless Steel Half Dome

Half Dome - Stainless Steel

External Slip Resistant Lens

Internal Clear (Double) Lens

Internal Clear (Double) Lens, attaches to Reflector

Internal Multi-directional Spread Lens

Internal Multi-Directional Spread Lens, attaches to Reflector

Internal Linear Spread Lens

Internal Linear Spread Lens, attaches to Reflector

Internal Honeycomb Louver

Internal Honeycomb Louver, attaches to Reflector

Internal Directional Louver

Internal Directional Louver, attaches to Reflector

Internal Ice blue Lens

Internal Ice blue Lens, attaches to Reflector

Internal Source Shield for Reflectors

Internal Source Shield, attaches to Reflector

Internal Snap-on Honeycomb Louver (PAR/R 20 lamp)

Internal Snap-on Honeycomb Louver. Lamp - PAR20
Accessory used in the following product(s): I3-H, I3-N, I3-SS, I3G-H, I3G-N, I32-SS, I32SS35HE, I32SS70HE, IL116-H, IL116G-H, IL116-N, IL116G-N, IL116-SS, IL136-H, IL136G-H, IL136-N, IL136G-N, IL136-SS, IT216-H, IT216-N, IT216-SS, IT216G-H, IT236-H, IT236-N, IT236-SS, IT236G-H, IT236G-N.

Internal Snap-on Honeycomb Louver (PAR/R 30 lamp)

Internal Snap-on Honeycomb Louver. Lamp - PAR30
Accessory used with the following products: I2, I2G, I3, I3G, I32, IL116-H, IL116G-H, IL116-N, IL116G-N, IL116-SS, IL136-H, IL136G-H, IL136-N, IL136G-N, IL136-SS, IT216-H, IT216-N, IT216-SS, IT216G-H, IT216G-N, IT236-H, IT236-N, IT236-SS, IT236G-H, IT236G-N.

Hadco I3/I3G Inground Landscape Light

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.
Lamping: 100W maximum PAR30/R30 or PAR38/R40 medium base lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in concrete and flush mounted with CP3 or CPS3.
Height: 11 1/2" (295mm)
Width: 9 5/8" (244mm)

I3-H
Inground w/Composite Ring

I3G-H
Inground w/Composite Rock Guard

I3-N
Inground w/Natural Brass Ring

I3G-N
Inground w/Natural Brass Rock Guard

I3-SS
Inground w/Stainless Ring

Hadco I3 Inground Landscape Light with Trim Ring

Finish

• (H) Bronze
• (N) Cast Bronze
• (SS ) Stainless Steel

Optics

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood
• (HA) Horizontal Asymmetric
• (H) Horizontal Symmetric
• (O) No Refl.*

Voltage

• 120V
• 208V
• 240V
• 277V

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.
Lamping: 100W maximum PAR30/R30 or PAR38/R40 medium base lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in concrete and flush mounted with CP3 or CPS3.
Height: 11 1/2" (295mm)
Width: 9 5/8" (244mm)

Hadco I3G Inground Landscape Light with Rock Guard

Finish

• (H) Bronze
• (N) Cast Bronze

Optics

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood
• (HA) Horizontal Asymmetric
• (H) Horizontal Symmetric
• (O) No Refl.*

Voltage

• 120V
• 208V
• 240V
• 277V

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.
Lamping: 100W maximum PAR30/R30 or PAR38/R40 medium base lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in concrete and flush mounted with CP3 or CPS3.
Height: 11 1/2" (295mm)
Width: 9 5/8" (244mm)

Concrete Pour Kit

Housing Only, I3

Housing Only When housing only is ordered for pre-shipment, add suffix "LH" (Lesss Housing) to complete catalog number to fixture without housing.

Accessory is used with the following product(s): I3-H, I3-N, I3-SS, I3G-H, I3G-N, I32-SS, I32SS35HE, I32SS70HE.

Internal Clear (Double) Lens

Accessory is used with the following product(s): I3-H, I3-N, I3-SS, I3G-H, I3G-N.

External Slip-Resistant Lens

Accessory is used with the following product(s): I3-H, I3-N, I3-SS, I3G-H, I3G-N.

Snap on Cut-Off Grill for PAR 36

Internal Snap-on Honeycomb Louver. Lamp - PAR36

Accessory used with the following products: I3, I3G.

Internal Snap On Honeycomb Louver, PAR38 Lamp

Accessory used with the following products: I3, I3G, I4, I4G, AG03, AG03G, AG02,AG02G

I3 External Glare Shield

Cast Aluminum Exterior Glare Shield

Accessory used with the following products: I3, I3G.

Hadco I4/I4G Inground Landscape Light

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: 2,600-pound live-load rated, standard walk-over lens. Clear convex, tempered soda-lime glass for high impact resistance. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.
Lamping: 150W maximum PAR38/R40 incandescent lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in concrete and flush mounted with CP4 or CPS4.
Height: 14" (354mm)
Width: 12 1/4" (310mm)

I4-H
Inground w/Composite Ring

I4G-H
Inground w/Composite Rock Guard

I4-H
Inground w/Cast Bronze Ring

I4G-H
Inground w/Cast Bronze Rock Guard

I4-SS
Inground w/Stainless Ring

Hadco I4 Inground Landscape Light with Trim Ring

Finish

• (H) Bronze
• (N) Cast Bronze
• (SS ) Stainless Steel

Optics

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood
• (HA) Horizontal Asymmetric
• (H) Horizontal Symmetric
• (O) No Refl.*

Voltage

• 120V
• 208V
• 240V
• 277V

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: 2,600-pound live-load rated, standard walk-over lens. Clear convex, tempered soda-lime glass for high impact resistance. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.
Lamping: 150W maximum PAR38/R40 incandescent lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in concrete and flush mounted with CP4 or CPS4.
Height: 14" (354mm)
Width: 12 1/4" (310mm)

Hadco I4G Inground Landscape Light with Rock Guard

Finish

• (H) Bronze
• (N) Cast Bronze

Optics

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood
• (HA) Horizontal Asymmetric
• (H) Horizontal Symmetric
• (O) No Refl.*

Voltage

• 120V
• 208V
• 240V
• 277V

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester. Single-piece molded silicone U-channel gasket.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: 2,600-pound live-load rated, standard walk-over lens. Clear convex, tempered soda-lime glass for high impact resistance. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern.
Lamping: 150W maximum PAR38/R40 incandescent lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in concrete and flush mounted with CP4 or CPS4.
Height: 14" (354mm)
Width: 12 1/4" (310mm)

Concrete Pour Kit

PVC Concrete Pour Kit

Accessory used in the following product(s): I4-H, I4-N, I4-SS, I4G-H, I4G-N.

Stainless Steel Concrete Pour Kit

Accessory used in the following product(s): I4-H, I4G-H, I4-N, I4G-N, I4-SS, I4-HHO.

Housing Only, I4

Housing Only When housing only is ordered for pre-shipment, add suffix "LH" (Lesss Housing) to complete catalog number to fixture without housing.

Accessory is used with the following product(s): I4-H, I4-N, I4-SS, I4G-H, I4G-N.

Internal Clear (Double) Lens

Accessory is used with the following product(s): I4-H, I4-N, I4-SS, I4G-H, I4G-N.

Internal Directional Louver, Laser Cut

Accessory is used with the following product(s): I4/I4G

External Slip-Resistant Lens

Accessory is used with the following product(s): I4-H, I4-N, I4-SS, I4G-H, I4G-N.

Internal Snap On Honeycomb Louver, PAR38 Lamp

Internal Honeycomb Louver for FL reflector. Lamp E-17 or PTL lamp.

Accessory used with the following products: I4, I4G.

Internal Honeycomb Louver for FL reflector (E17 or PLT lamp)

Internal Honeycomb Louver for FL reflector. Lamp E-17 or PTL lamp.

Accessory used with the following products: I4, I4G.

Internal Honeycomb Louver for SP reflector. Lamp E-17

Accessory used with the following products: I4, I4G.

Cast Aluminum Exterior Glare Shield

Accessory used with the following products: I4, I4G.

Internal Multi-Directional Spread Lens

Accessory used with the following products: I4, I4G.

Hadco I5 Composite Inground Landscape Light for use with Par Lamps

Finish

• (H) Bronze

Optics

• (O) No Refl.*
• (FL ) Flood
• (SP ) Spot
• (H) Horiz.

Voltage

• 120V
• 208V
• 240V
• 277V

In compliance with the 2005 Energy Policy Act (EPAct2005), we no longer offer Mercury Vapor Products.

Please note all 150-500w mh fixtures are In compliance with title 20 / EISA.

Housing: Fasteners are 300 series stainless steel. Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Two (2) ¾" NPS threaded conduit inlets on bottom. Two (2) additional inlets may be field drilled and tapped. gasketing is silicone. Rock guard used for directional glare control made of natural cast bronze. Dark bronze polyester composite (standard).
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: 360° horizontal rotation adjustment. For E17, E28 and T15 vertical lamps: 15° adjustment either side of vertical. For E17 horizontal lamps: 25° vertical adjustment. For PAR38 and R40 lamps: 30° vertical adjustment. Reflectors for E17, E28 and T15 vertical lamps are specular spun aluminum. Reflectors for E17 horizontal lamps are a combination of Hammertone and specular formed aluminum. 3/8" thick, clear, high-impact tempered glass. Lens is crowned and mounted flush with lens retainer to resist debris accumulation. 1,300 pound live load (walkover rated).
Lamping: Pulse-rated, heavy-duty glazed porcelain for Medium and Mogul Base lamps.
BALLAST: HID ballasts are HPF core and coil, factory wired and tested, mounted to a key-slotted removable tray with quick disconnect for easy Installation: . Ballasts shall provide +/-5% lamp power regulation with +/-10% input voltage regulation. Fluorescent ballast is electronic (-20° F cold weather start).
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when used in concrete and flush mounted with CP4 or CPS4.
Height: 12 1/4"
Width: 19 5/16" (491mm)

Hadco IF218/IF226/IF232 Small Fluorescent Line Voltage Inground Landscape Lighting

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Rock guard used for directional glare control made of compression molded polyester.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens.
Lamping: Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. 26W Fluorescent socket is a GX24Q-3 base. 32W Fluorescent socket is a GX24Q-3 base. 18W Fluorescent is a GX24q-2 socket.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when flush mounted with CP2 or CPS2.
Height: 8 1/4" (210mm)
Width: 6 5/8" (169mm)

Hadco IL116/IL136 Composite Low Voltage Inground Landscape Lighting

IL116
Lamping: 75W maximum MR16 bi-pin lamp. Covered MR16 are recommended to protect lamps inner capsule. Lower wattage lamps are acceptable.

IL136
Lamping: 75W maximum PAR 36/AR11 screw terminal lamp.  Lower wattage lamps are acceptable. 

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens. Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern. Electrical Assembly: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when flush mounted with CP2 or CPS2.
Height: 8 7/16" (214mm)
Width: 6 5/8" (169mm)

IL116-H
Inground w/Bronze Brass Trim

IL116G-H
Inground w/ Bronze Rock Guard

IL116-N
Inground w/Natural Brass Ring

IL116G-N
Inground w/Natural Brass Rock Guard

IL136-SS
Inground w/Stainless Ring

Hadco ILM5D4, ILN5D4, ILW5D4 (IL_5D4) LED Low Voltage Micro Inground Landscaping Light

LED (light emitting diode) included

Finish

• (A) Black
• (G) Verde
• (H) Bronze

Housing: Cool external temperatures - all below 38ºC - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85ºC for composite, 80ºC for glass) and 4 seconds (74ºC for composite, 70ºC for glass) of contact. One-piece injection molded ULTEM^® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM^® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance. Fasteners are 300 series stainless steel.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Integral collimating spot (8°) optics. Integral collimating narrow flood (24°) optics. Integral collimating wide flood (40°) optics. Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal.
Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (4,000K nominal). Warm white (3,000K nominal). Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. (magnetic low voltage transformer required). Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts (high power) or 5 total watts (low power). Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40ºC/F minimum starting temperature. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Fixture is pre-wired and potted to prevent water entry. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. Low voltage transformer must be ordered to power the fixtures. 12 Volt system requires remote transformer, not included.
WARRANTY: 5 year extended warranty
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).
LED SPECIFICATIONS: A magnetic Hadco low voltage transformer must be used with Hadco LEDs
Height: 4 3/8" (111mm)
Width: 4 1/8" (105mm)

Height: 4 3/8" (111mm)
Width: 4 1/8" (105mm)

Hadco IT216, IT236 IT2 Small WelLyte Line Voltage Inground Landscaping Light

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Trim ring is a compression molded polyester. Trim ring is a die-cast stainless steel. Trim ring is natural cast bronze. Rock guard used for directional glare control made of compression molded polyester.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Lamps have 15° articulation either side of vertical and 358° rotation without interruption of beam pattern. Clear convex, tempered soda-lime glass for high impact resistance. 2,200-pound live-load rated, standard walk-over lens.
Lamping: 75W maximum PAR 36/AR11 screw terminal lamp. 75W maximum MR16 bi-pin lamp. Lamp is not included. Lower wattage lamps are acceptable. (Note: PAR20/R20 and PAR30/R30 are not aimable.). Electrical Assembly: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. Double screw terminal socket. Step-down transformer reduces line voltage to 12 volts.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA Compliant when flush mounted with CP2 or CPS2.
Height: 8 13/16" (224mm)
Width: 6 5/8" (169mm)

IT216-H
Inground w/Bronze Brass Trim

IT216G-H
Inground with Bronze Rock Guard

IT216-N
Inground w/Natural Brass Ring

IT216G-N
Inground w/Natural Brass Guard

IT216-SS
Inground w/Stainless Ring

Hadco IUL516 Ultem Micro Inground 12v Low Voltage Composite Inground Landscaping Light

Available in Bulk Packs (25 Units)
IUL516-HBAB25 MR16 Inground with Lamp (25 Units)
IUL516-HBULK25 MR16 Inground Fixture Bulk Pack (25 units)

Housing: One-piece injection molded ULTEM^® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM^® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance.
Finish: Composite is textured, pressure formed, molded-in-color.
OPTICAL ASSEMblY: Clear convex, tempered glass furnished with silicone O-ring for watertight seal.
Lamping: 35W maximum MR16 bi-pin lamp. Lower wattage lamps are acceptable. Covered MR16 are recommended to protect lamps inner capsule. Electrical Assembly: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
ACCESSORIES: IBL16 Ice blue Lens. ISL16 Spread Lens. IAS16 Linear Spread Lens. ICG16 - Internal snap on Honeycomb louver (Lamp MR16). CP5 - Concrete Pour Kit.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 4 3/8" (111mm)
Width: 4 1/8" (105mm)

Inground Installation

1. Excavate soil for fixture placement and conduit runs. Allow a minimum of 3" around and under housing for drainage material.

2. Remove the screws from the glass/ gasket assembly and wiring compartment cover. Connect conduit fittings to housing conduit entries utilizing a thread sealant, and tighten to 40 ft-lbs. max. DO NOT REMOVE the moisture absorbing desi-pak from inside the fixture.

3. Connect 120V leads in wiring compartment to supply wires. Make ground connection. The contractor must pull ground wire or make a ground connection to the metal conduit system.

4. Conduit entries must be potted to prevent water entry (3M 4442 GELA supplied with I3 and I4). Replace the wiring compartment cover.

5. Install the ballast tray. Plug lamping module into quick connect, if applicable.

6. Install the correct lamp. DO NOT EXCEED the maximum wattage marked on the fixture.

7. Clean gasket seating surfaces. Screw holes can be blown clear or cleared with a #10-24 tap. Insert screws through lid and tighten using an alternating torque sequence to 20 (min.) 30 (max.) inch-lbs.

8. Fixture housing should be surrounded by a 3" (minimum) layer of sand or gravel to ensure drainage. Materials such as vermiculite and bark are for ground cover only. Full depths of these may cause overheating. In concrete pour cases, the housing is placed on a 4" (minimum) bed of gravel, with soil below. Do not install fixtures where water collects arid stands for any Length of time.