Hadco LED Landscape Lighting
LED (Light Emitting Diode) Landscape Lights

Hadco LED Polycarbonate BrickLytes

Housing: Die-cast aluminum faceplate with galvanized steel, single gang recessed box with stainless steel fasteners. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Gasketing is silicone. Fasteners are 300 series stainless steel. Note: Recessed housing contains four (4) ½" NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications. Zinc-rich primer and thermoset powdercoat for durability.
12 Volt Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is pre-wired with 6-ft. pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.
Finish: A Black, H Bronze
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG Black, white, and ground wires.
WARRANTY: Three-year limited warranty.
LED WARRANTY: Five-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards. ADA Compliant when used in indoor and outdoor wall applications.
ADA Compliant – Compliant when used in indoor and outdoor wall applications. ETL, cETL Listed.

Compare Brick Lights & Paver Lights...>

Hadco RSS2 LED Polycarbonate BrickLytes
OPTICAL ASSEMblY: Specular aluminum formed reflector. Clear UV stabilized injection molded polycarbonate with 45 degree louvered screen insert.
Lamping: 18W CFL (G24Q-2). 13W CFL (GX23D-2). 40W maximum T10 (4KV medium base porcelain socket). Lower wattage lamps are acceptable.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. 18W Fluorescent is a GX24q-2 socket.
LED Electrical Assembly: Pre-wired with high temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40ºC/F minimum starting temperature.

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

Hadco RSF2 LED Polycarbonate Brick Light

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

Hadco Louver BrickLytes

Housing: Aluminum parts have zinc-rich primer and thermoset powdercoat for durability. Faceplates are color-impregnated. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Die-cast aluminum trim contains less than 0.3% copper to resist corrosion. Thermal Protection device is required for installations in drywall, plaster, wood or other non-masonry materials.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Zinc-rich primer and thermoset powdercoat for durability.
OPTICAL ASSEMblY: The cast louver offers lower light levels with cut-off for lighting stairways or general lighting where shielding of the light source is more important than high light levels.  Symmetric reflector is precision formed, steel with a white reflective coating. Horizontal louver lens made of die-cast copper-free aluminum with a 45° cutoff and frosted tempered glass. Cast bronze louver is natural cast bronze with frosted tempered glass.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards. ADA Compliant when used in indoor and outdoor wall applications.

Compare Brick Lights & Paver Lights...>

Hadco RSC2 LED Aluminum Louver Brick Light

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

Hadco RSC2 LED Natural Brass Louver Brick Light
Finish: N Natural Brass
Natural Brass louver is Natural Brass with frosted tempered glass.
120 Volt Lamping: 9W PLS Fluorescent (G23). 13W PLC Fluorescent (120V: GX23-2; 277V: G24Q-1). 18W CFL (G24Q-2). Two 18W maximum S-8 (1141) lamps (Single contact bayonet base). 40W maximum T10 (4KV medium base porcelain socket). Lower wattage lamps are acceptable.
12 Volt Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is pre-wired with 6-ft. pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG Black, white, and ground wires. 1141 lamps use an integral 120V/12V transformer.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal).
LED Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40ºC/F minimum starting temperature. Pre-wired with high temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs.

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

Hadco RSV2 LED Aluminum Louver Brick Light

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

Hadco RSV2 LED Natural Brass Louver Brick Light

LED – Deliver 70% lumen maintenance at 50,000 hours. Cool white (5,500K nominal). Amber lens option (3,000K). 3 LED: 10.4 total watts. 5 LED: 13.5 total watts.

LED Underwater Light ULW5D4
Specialty Low Voltage Landscape Light

Hadco ULW5D4 LED Underwater Light
Low Voltage LED Pond Light

NEW Now Available in:

• LED Color Temperature: (W) Warm or (C) Cool
• Output: (H) High or (L) Low
• Finish: (A) Black, (G) Verde* or (H) Bronze
  Finish: Composite is textured, pressure formed, molded-in-color.

Housing: Cool external temperatures - all below 36ºC - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74ºC for coated metal, 80ºC for glass) and 4 seconds (61ºC for coated metal, 70ºC for glass) of contact. One-piece injection molded ULTEM^® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM^® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance. Fasteners are 300 series stainless steel.
OPTICAL ASSEMblY: Warm (3000K), amber-colored tempered glass lens. Integral collimating flood (25°) optics.
Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40ºC/F minimum starting temperature. Standard 10 ft. 18-2, 105° C, STWA water-resistant cord. Fixture is prewired and potted to prevent water entry. Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. (magnetic low voltage transformer required). Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts (high power) or 5 total watts (low power). 12 Volt system requires remote transformer, not included.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).
Height: 6 11/16" (170mm)
Width: 4 1/16" (103mm)

More Hadco Underwater Lights and Pond Lights >

Height: 6 11/16" (170mm)
Width: 4 1/16" (103mm)
Max. Weight: 5.04 lb.

Hadco I2.5 LED Inground Landscape Light

• (SP ) Spot
• (NF) Narrow Flood
• (FL ) Flood

LED (Light Emitting Diode) Included
Smart select driver: 120-277 vac 50/60 Hz auto-sensing

Description
The revolutionary i2.5 composite inground provides optimum performance in a small aperture luminaire. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i2.5 reinforces HADCO's position as the leader in landscape lighting. Now available with LED!

More Hadco Inground Landscape Lighting & Well Lights >

Housing: Separate sealed compartments provide isolation between field wiring, optics, and ballast (CFL). Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through. Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts. Cast cover to match trim ring with two captive stainless steel slotted Phillips machine screws for access. Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted, silicone- gasket cover. Rock guard made of cast brass (natural finish) or cast stainless steel (satin finish). Ring is factory pre-drilled for optional guard. Trim ring is natural cast bronze or cast stainless steel. Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.) Half dome 360 degree field adjustable for glare control, constructed of natural cast brass (natural finish) or cast stainless steel (satin finish) to match lens ring. Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up.
Finish: Natural Brass has satin matte finish. Stainless Steel has satin matte finish.
Lamping: 5,000K color temperature (CCT) or 3,000K amber coated tempered glass lens. Approximately 50,000 hours of operational life (at 25 C ambient temperature and 70% lumen maintenance). >80 CRI.
OPTICAL ASSEMblY: Clear, flat, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded 100% silicone gasket, factory adheared. Optional lens assemblies include cool touch lens, reducing lens temperatures by 35%, ice blue lens, linear or multi-directional spread lens. Sealed optical chamber. Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less LOC-AIM^®. Handle enables easy tool-less removal of optical assembly for hot aiming and re-lamping, simply press-fit back into place. Electrical Assembly: Smart Select Electronic Driver 120 to277 VAC input; 50-60Hz; auto-sensing. Operating start temperature -40 C (-40 F) 17watts consumed (total fixture consumption)
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards. ADA compliant when used in concrete and flush mounted with CPS25.
WARRANTY: Ten-year limited warranty.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).

Hadco WAML1D, WBML1D Low Voltage LED Flood Light
Mini Architectural Flood Light with Shroud

Finish: Black, White, Verde, Bronze
Finish: Exterior Coating: Either Urethane or Triglycidyl Isocyanurate (TGIC) Polyester Powder to a minimum dry film thickness of 2.0 mils (0.002") for urethane powder, or 3.0 mils (0.003") for TGIC powder. The coating is electrostatically applied and cured in a gas fired convection oven by heating to a minimum of 350°F and a maximum of 400°F. Following a 5-stage conversion cleaning process, the components are finished with a super-durable, electrostatically applied, thermoset polyester powdercoat which is bonded by heat fusion thermosetting. The finish is laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Housing: 380 die-cast aluminum alloy. Fasteners are 300 series stainless steel to prevent corrosion and ensure longer life. gasketing is silicone. Fully-adjustable swivel arm with vibration-proof locking teeth. 1/2" NPS male threads to screw onto accessory mounting stake or junction box, sold separately.
OPTICAL ASSEMblY: Clear or frosted tempered glass lens.
Lamping: Cool White (6,000K) Warm White (3,000K) Lamp is included with fixture. Electrical Assembly: 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. 12 Volt system requires remote transformer, not included. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. (magnetic low voltage transformer required). Integral surge protector built into LED driver circuit. 12 volts, 6.4 total watts (high wattage) or 3.7 total watts (low wattage).
WARRANTY: 5 year extended warranty
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 4 7/8" (123mm)
Width: 6 7/8" (175mm)
Length: 5" (127mm)

More Hadco FloodLytes & LED Flood Lights >

Hadco TRL4D Small Tudor Die-cast Aluminum LED PathLyte

Housing: Cool external temperatures - all below 43ºC - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74ºC for coated metal, 80ºC for glass) and 4 seconds (61ºC for coated metal, 70ºC for glass) of contact. Die-cast aluminum. Stem is extruded aluminum. 1/2" NPS male threads to screw onto accessory mounting stake or junction box, sold separately. Fasteners are 300 series stainless steel.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.
OPTICAL ASSEMblY: Sealed collimating optics with diffuser lens for even light distribution.
Lamping: Philips Lumiled Rebel, Warm White (3,000K)
Electrical Assembly: Low voltage transformer must be ordered to power the fixtures. Input voltage range (VAC): 10.8 - 17.0. 6.5 total watts consumed. OptoElectronix electronic LED driver. UL Class 2 -10°C to 50°C mimum starting temperature. Internal surge protector built into LED driver circuit Connects directly to 12V AC or 12V DC power source. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
WARRANTY: Three-year limited warranty.
IP RATING: IP66: Dust-tight and sealed against direct jets of water.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 19 1/2" (495mm)
Width: 5 1/16" (129mm)

More Hadco Cool or Warm LED Path Lights >

Hadco BL5016 MR16 or LED EnduraLED Micro BulLyte

The housing is constructed of double gasketed, die cast marine-Grade alloy aluminum for long life. With vibration-proof serrated teeth along with the base of the housing, it provides a positive lock. A 360 degree fully adjustable swivel arm allows for precise lighting along with an angled lens for self-cleaning. The fixture is UL, cUL listed for a 50 watt MR16 lamp or LED. The socket features a retention clip to secure the lamp in place.

Hadco BL5016 LED EnduraLED Micro BulLyte
Cool 4000K or Warm 2700K LED 7W MR16
Lamping: 35w consumption features active cooling technology to disperse heat.  White high brightness (HB) LEDs. Delivers 70% lumen maintenance at 20,000 hours. Cool white (4,000K nominal). Warm white (2,700K nominal). Instant-on light. Emits virtually no UV/IR light beam. 20,000+ hours rated life. No UV and Cool Beam (no IR). 
OPTICAL ASSEMblY: Clear tempered glass affixed at 10° angle for natural cleaning. 24° beam angle for a clearly defined beam spread. Electrical Assembly: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. Stainless steel retention clip affixed to socket to securely hold lamp in place. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Hadco BL5016 MR16 Micro BulLyte
Lamping: 50W maximum MR16 bi-pin lamp. Lower wattage lamps are acceptable. Covered MR16 are recommended to protect lamps inner capsule.
OPTICAL ASSEMblY: Clear tempered glass affixed at 10° angle for natural cleaning. Electrical Assembly: Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. Stainless steel retention clip affixed to socket to securely hold lamp in place. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-Up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Available BulLyte MR16 Bulk Pack (25 Units)
BulLyte MR16 Bulk Pack (25 Units) with Stake
BulLyte MR16 Bulk Pack (25 Units) with Lamp, Stake

Finish: Black, Verde, Bronze, Speckled Stone, Sienna
Housing: Die-cast marine grade aluminum alloy. Fully-Adjustable swivel arm with vibration-proof locking teeth. Fully rotatable shroud, double gasketed, die-cast marine grade alloy aluminum. 1/2" NPS male threads to screw onto accessory mounting stake or junction box, sold separately. gasketing is silicone. Fasteners are 300 series stainless steel.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.

WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Width: 2 13/16" (71mm)
Length: 5 13/16" (147 mm)
Max. Weight: 1.48 lb

More Hadco LED Directional Bullets >
More Hadco Night Life Directional Landscape Lighting Bullets >

• Clear tempered glass affixed at 10° angle for natural cleaning
  
• High temperature adhesive
  
• Die cast marine grade alloy aluminum
  
• Stainless Steel shroud-locking machine screw
  
• Serrated teeth for positive lock
  
• Die cast locking nut
  
• Stainless Steel Phillips locking screw Black WC coated
  
• Specular aluminum heat shield
  
• Fixed socket with high temperature Teflon leads mounted to heat sink
  
• Double molded silicone gaskets
• 1/2" N.P.S. fitter
  
• Shroud is fully rotaTable at 360°
  
• Die cast marine grade aluminum
  
• Internal mounting of shroud to insure waterproof operation in any position of fixture