Hadco Mini StepLytes (Step Lights)

Hadco Low Voltage Mini StepLytes

Housing: Housing and finish ring are die-cast aluminum. Aluminum housing contains less than 0.3% copper to prevent corrosion in concrete applications. Flange made of die-cast aluminum containing less than 0.3% copper to resist corrosion. Single-piece molded silicone gasket to prevent water, dust, and insect filtration. Fasteners are 300 series stainless steel.  Internal wiring compartment contains two (2) 1/2" NPT conduit taps in the bottom and one (1) 1/2" NPT conduit tap in both sides. A removable plug will be provided for one (1) tap. 
12 Volt Electrical Assembly: Single contact bayonet (S-8). Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 volt fixture is pre-wired with 6-ft. pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG Black, white, and ground wires. Double contact bayonet socket type (BA15d).
ACCESSORIES: MAKM - Masonry construction mounting kit. MAKNS - New stud wall construction mounting kit. MAKES - Existing stud wall construction mounting kit.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards. ADA Compliant when used in indoor and outdoor wall applications.

Note: All units supplied with mounting hardware for concrete pour Installation: . If other mounting kits are required, order accessory above.

12 Volt RRBL13, RRBL14, 120 Volt RRB1 Polycarbonate

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

12 Volt RRCL12, RRCL13, 120 Volt RRC1I Aluminum

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

12 Volt RRFL13, RRFL14, 120 Volt RRF1 Polycarbonate

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

Hadco Line Voltage Mini StepLytes

Housing: Die-cast aluminum. Internal wiring compartment contains two (2) ½" NPT conduit taps in the bottom and one (1) ½" NPT conduit tap in both sides. A removable plug will be provided for one (1) tap. Gasketing is silicone. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Fasteners are 300 series stainless steel.
Finish: Zinc-rich primer and thermoset powdercoat for durability.
OPTICAL ASSEMblY: Symmetric reflector is precision formed, semi-specular aluminum or highly polished aluminum, which produces a wide symmetric distribution for general area lighting. UV stabilized injection molded clear polycarbonate bubble lens, allowing positioning of lamp to project out of the wall enabling and efficient wide distribution. Electrical Assembly: 26W Fluorescent socket is a GX24Q-3 base. 32W Fluorescent socket is a GX24Q-3 base. 42W Fluorescent socket is a GX24Q-4 base. Bi-pin socket type (GY6.35) with 250° C high temperature teflon coated wire leads. 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. Fixture is pre-wired with 18 AWG Black, white, and ground wires.
BALLAST: HID ballasts are HPF core and coil, factory wired and tested, mounted to a key-slotted removable tray with quick disconnect for easy Installation: . Ballasts shall provide +/-5% lamp power regulation with +/-10% input voltage regulation. Fluorescent ballast is electronic (-20° F cold weather start).
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards. ADA Compliant when used in indoor and outdoor wall applications.

120 Volt RRB3 Polycarbonate

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

120 Volt RRC3 Aluminum

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

Hadco LineLyte 12 Volt Copper Step Light

HADCO's new LineLyte Series provides a unique way to enhance your deck or patio area. Available in Lengths ranging from 6" to 24", these natural copper fixtures mount easily under steps or railings to provide illumination for atmosphere and safety without the need to cut holes in or deface step risers. They mount with (2) screws via key slots on the top of the fixture. These fixtures use a 10,000 hour Xenon T3 lamp (included) for superior lighting and low maintenance while the socket swivels down for easy re-lamping.

Above: LLL AC Antique Copper StepLytes
Below: LLL SS Stainless Steel StepLytes

Mount using Stainless wood screws (supplied) via key slots or use Mounting Plate MPLLL.

LineLyte Copper StepLyte & Deck Lights

AC Antique Copper StepLyte
Housing: Seamless solid copper extrusions with solid copper ends. Tool-less lamp access.
Finish: Natural Copper is bright polished, untreated copper. Color will age naturally to a fine dark copper patina.

SS Stainless Steel StepLyte
Housing: Stainless Steel. Bottom is open. Tool-less lamp access. Easy access to lamp.
Finish: Linear machine brushed, satin appearance.

OPTICAL ASSEMblY: Reflector is Stainless Steel.
Lamping: 10W wedge base T3 1/4 (xenon) lamp is included with fixture. Xenon lamp life is approximately 10,000 hours. Lower wattage lamps are acceptable. Lamp does not need to be protected and can be directly handled. Electrical Assembly: Wedge base socket type (T3-1/4 or T5). Socket is hinged for easy relamping. 12 volt fixture is pre-wired with 6-ft. pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
Installation: & Mounting: Two (2) Stainless #8 wood screws (supplied) via key slots. Or use Mounting Plate MPLLL.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 1" (25mm)
Width: 1" (25mm)

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

LineLyte Mounting Plate (MPLLL)

Finish: Stainless Steel has satin matte finish. Natural Copper is bright polished, untreated copper that will age naturally to a fine dark copper patina.
Mounting: Brackets attach to LineLyter with two hex nuts (included).

Bracket is inserted between two blocks or bricks, held in place by the top block.

Hadco DeckLytes DUL1 Composite, DCL1 Brass, DAL1 Aluminum, DAL1-SS Stainless Steel

OPTICAL ASSEMblY: Frosted, annealed glass lens Reflector is a stamped specular aluminum.
Lamping: 10W maximum T3 bi-pin lamp. 10W T3 lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 volt fixture is pre-wired with 6-ft. pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
Installation: & Mounting: Two (2) Stainless #8 wood screws (supplied) via key slots.
WARRANTY: Ten-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2008 Standards.

Hadco DeckLyte DUL1 Composite
Housing: One-piece injection molded ULTEM^® High Performance Polymer composite. Fasteners are 300 series stainless steel.
Finish: Composite is textured, pressure formed, molded-in-color.
Finish: image A Black, G Verde, H Bronze
WARRANTY: Ten-year limited warranty.

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

Hadco DeckLyte DCL1 Brass
Housing: Die-cast brass. Fasteners are 300 series stainless steel.
Finish: Natural Brass (N) is as-cast and tumble polished.
Finish: N Natural Brass
WARRANTY: Lifetime limited warranty.

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

Hadco DeckLyte DAL1 Aluminum
Housing: Body and mounting plate are cast aluminum construction. Fasteners are 300 series stainless steel.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.
Finish: A Black, B White, G Verde, H Bronze, T Speckled Stone, U Sienna
WARRANTY: Three-year limited warranty.

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>

Hadco DeckLyte DAL1-SS Stainless Steel
Housing: Body and mounting plate are cast stainless steel construction.
Fasteners are 300 series stainless steel.
Finish: Linear machine brushed, satin appearance.
Finish: SS Stainless steel (Matte Finish)
WARRANTY: Lifetime limited warranty.

Compare Mini Step Lights, Mini Wall Lights & Deck Lights...>