Hadco Tudor Path Lights - Low Voltage, Line Voltage and LED

Hadco TKL1 Tudor Die-cast Aluminum Low Voltage PathLyte

Housing: All cast aluminum construction. 1/2" Schedule 40 Aluminum stem 18" long threads to screw on to accessory mounting stake (included) or junction box (sold separately).
Finish: Hand-rubbed verde antiqued over Black thermoset powdercoat.
Lamping: Lamp is included with fixture. Xenon lamp life is approximately 10,000 hours. Higher wattages may be used only with glass panels installed. 18W maximum wedge base T-5 Xenon. Electrical Assembly: 12 Volt system requires remote transformer, not included. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt fixture is pre-wired with 4-ft pigtail of 18-2 AWG. Wedge base socket type (T3-1/4 or T5).
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations.
Height: 22 7/8" (581mm)
Width: 6 5/8" (168mm)

Hadco TL19 Tudor Die-cast Aluminum Low Voltage PathLyte

Hadco TRL4 Small Tudor Die-cast Aluminum Low Voltage PathLyte

TRL4-G Verde
TRL4-T Speckled Stone
TRL4-U Sienna
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Available Bulk Pack TRL4-G Verde
Bulk Pack (25 Units) TRL4-GBULK25 with Lamp
Bulk Pack (25 Units) TRL4-GS725 with Lamp, Stake

Housing: Die-cast aluminum. Stem is extruded aluminum. Roof has dual stainless steel hinge with stainless steel spring-lock for tool-less entry and relamping. 1/2" NPS male threads to screw onto accessory mounting stake or junction box, sold separately.
OPTICAL ASSEMblY: Spun aluminum reflector with white thermoset powdercoat. Frosted tempered glass sprinkler shield includes top and bottom silicone gaskets for tight seal.
Lamping: 20W maximum T3 bi-pin lamp. Lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 23 7/16" (597mm)
Width: 8 5/16" (211mm)

Also available in Cool or Warm LED

Hadco TRL4D Small Tudor Die-cast Aluminum LED PathLyte

Housing: Cool external temperatures - all below 43ºC - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74ºC for coated metal, 80ºC for glass) and 4 seconds (61ºC for coated metal, 70ºC for glass) of contact. Die-cast aluminum. Stem is extruded aluminum. 1/2" NPS male threads to screw onto accessory mounting stake or junction box, sold separately. Fasteners are 300 series stainless steel.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.
OPTICAL ASSEMblY: Sealed collimating optics with diffuser lens for even light distribution.
Lamping: Philips Lumiled Rebel, Warm White (3,000K)
Electrical Assembly: Low voltage transformer must be ordered to power the fixtures. Input voltage range (VAC): 10.8 - 17.0. 6.5 total watts consumed. OptoElectronix electronic LED driver. UL Class 2 -10°C to 50°C mimum starting temperature. Internal surge protector built into LED driver circuit Connects directly to 12V AC or 12V DC power source. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.
WARRANTY: Three-year limited warranty.
IP RATING: IP66: Dust-tight and sealed against direct jets of water.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 19 1/2" (495mm)
Width: 5 1/16" (129mm)

More Hadco Cool or Warm LED Path Lights >

Hadco TR5 Tudor Die-cast Aluminum Line Voltage PathLyte

Lamping: 100W maximum A19 lamp. Lamp is not included. Lower wattage lamps are acceptable. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. Fixture is pre-wired with 18 AWG Black, white, and ground wires.

Hadco TRL5 Tudor Die-cast Aluminum Low Voltage PathLyte

Lamping: 35W maximum T3 halogen. Lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included. 12 Volt system requires remote transformer, not included.

Housing: Die-cast aluminum. Roof has dual stainless steel hinge with stainless steel spring-lock for tool-less entry and relamping. Stem is extruded aluminum. Fasteners are 300 series stainless steel. 1/2" NPS male threads to screw onto accessory mounting stake or junction box, sold separately.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.
OPTICAL ASSEMblY: Frosted tempered glass sprinkler shield includes top and bottom silicone gaskets for tight seal. Reflective white powdercoat on underside of roof.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001:2000 Standards.
Height: 28 1/8" (715mm)
Width: 9 7/8" (251mm)