Hadco Underwater Lights for Pools, Fountains & Pond Lights

Hadco UWL2075, UWL2100 Cast Bronze Low Voltage Niche Mounted Underwater Lights

UWL2075-N 75W MR16*
Lamping: 75W MR16 lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (GY6.35) with 250° C high temperature teflon coated wire leads. Standard 10 ft. 16-3 AWG, 105° C, STOW water-resistant cord. Fixture is pre-wired and potted to prevent water entry.

UWL2100-N 100W T3*
Lamping: 100W maximum T3 bi-pin lamp. 100W T4 lamp is included with fixture. Electrical Assembly: Bi-pin socket type (GY6.35) with 250° C high temperature teflon coated wire leads. Standard 10 ft. 16-3 AWG, 105° C, STOW water-resistant cord. Fixture is pre-wired and potted to prevent water entry.

Housing: Fasteners are 300 Series stainless steel. Rockguard is marine grade bronze. Spun stainless steel. Spun stainless steel with cast nickel bronze trim. Stainless steel with integral bonding lugs and hub for connecting 1/2" or 3/4" conduit. Integral and furnished as standard on all fixtures. This enables fixture to be used in accordance with NEC Article 680-51 in installations without an external low-water cutoff.
Finish: Natural Brass will age over time, can be field painted.
Optical Assembly: Clear convex, tempered glass furnished with silicone O-ring for watertight seal.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards.
CORROSIVE CONDITIONS: Proper pH balance is required when using copper and brass lighting fixtures in corrosive applications. If the water was allowed to remain in acid conditions, with chlorine or bromine present, copper corrosion occurs. Our laboratory testing concludes that chlorine/bromine does work better at a pH below 7.2. However, there are consequences that will result. Corrosion can present a problem below 7.0. As the pH falls below 7.2, chlorine/bromine can become increasingly more aggressive and irritating. Brass and copper fixtures will experience some natural patina. The fixture will turn a darker brown color as the patina process occurs.
Height: 5 1/8" (130mm)
Width: 7 7/16" (189mm)

Line Voltage Version shown below.

Hadco UWL1 Composite 12 Volt Underwater Light

Housing: Molded Lexan composite, internally weighted. Single-piece molded silicone gasket to prevent water, dust and insect filtration. Optional reflector to block uplight (included).
Finish: Composite is textured, pressure formed, molded-in-color.
Optical Assembly: Molded prismatic acrylic polycarbonate to allow adjustable light distribution.
Lamping: 20W maximum T3 bi-pin lamp. 10W T3 lamp is included with fixture. Lower wattage lamps are acceptable. Electrical Assembly: Bi-pin socket type (G4) with 250° C high temperature teflon coated wire leads. Standard 10 ft. 16-3 AWG, 105° C, STOW water-resistant cord. Fixture is pre-wired and potted to prevent water entry.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards.
Height: 3" (76mm)
Width: 5" (127mm)

LED Underwater Light ULW5D4
Specialty Low Voltage Landscape Light

Hadco ULW5D4 LED Underwater Light
Low Voltage LED Pond Light

NEW Now Available in:

• LED Color Temperature: (W) Warm or (C) Cool
• Output: (H) High or (L) Low
• Finish: (A) Black, (G) Verde* or (H) Bronze
  Finish: Composite is textured, pressure formed, molded-in-color.

Housing: Cool external temperatures - all below 36°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact. One-piece injection molded ULTEM^® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM^® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance. Fasteners are 300 Series stainless steel.
Optical Assembly: Warm (3000K), amber-colored tempered glass lens. Integral collimating flood (25°) optics.
Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature. Standard 10 ft. 18-2, 105° C, STWA water-resistant cord. Fixture is prewired and potted to prevent water entry. Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. (magnetic low voltage transformer required). Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts (high power) or 5 total watts (low power). 12 Volt system requires remote transformer, not included.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: UL Listed to U.S. safety standards for wet locations. cUL Listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards.
IP RATING: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).
Height: 6 11/16" (170mm)
Width: 4 1/16" (103mm)

More LED Landscape Lighting >

Height: 6 11/16" (170mm)
Width: 4 1/16" (103mm)
Max. Weight: 5.04 lb.

Hadco UWUL5 Composite 12 Volt Underwater Light

Built to last with injection molded fiberglass reinforced Ultem High Performace Polymer, the UWUL516 composite underwater fixture delivers the signature engineering and durable construction of Hadco.

Housing: One-piece injection molded ULTEM^® High Performance Polymer composite. Fasteners are 300 Series stainless steel. Lens ring is a Single-piece injection molded ULTEM^® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance.
Optical Assembly: Clear tempered glass lens.
Lamping: 50W maximum MR16 bi-pin lamp. Lower wattage lamps are acceptable. Lamp is not included. Electrical Assembly: Standard 10 ft. 18-2, 105° C, STWA water-resistant cord. Fixture is prewired and potted to prevent water entry. Bi-pin socket type (GU5.3) with 250° C high temperature teflon coated wire leads. 12 Volt system requires remote transformer, not included.
Mounting: Weighted concrete with swivel to allow up to 90° aiming.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards.
Height: 6 11/16" (170mm)
Width: 5 1/8" (130mm)

Hadco UW1100-N, UW1250-N Cast Bronze Line Voltage Freestanding Underwater Lights

UW1100-N 120V 100W T4*
Lamping: 100 W Maximum Incandescent 100W T4 lamp is included with fixture. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. Standard 10 ft. 16-3 AWG, 105° C, STOW water-resistant cord. Fixture is pre-wired and potted to prevent water entry.

UW1250-N 120V 250W T4*
Lamping: 250W maximum. 250W T4 lamp is included with fixture. Electrical Assembly: 4kv rated medium base porcelain socket. Nickel-plated screw shell with center contact. Standard 10 ft. 16-3 AWG, 105° C, STOW water-resistant cord. Fixture is pre-wired and potted to prevent water entry.

Housing: Fasteners are 300 Series stainless steel. gasketing is silicone. Spun stainless steel. Marine grade bronze swivel yoke. Rockguard is marine grade bronze. Integral and furnished as standard on all fixtures. This enables fixture to be used in accordance with NEC Article 680-51 in installations without an external low-water cutoff.
Finish: Natural Brass (N) is as-cast and tumble polished.
Optical Assembly: Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards.
CORROSIVE CONDITIONS: Proper pH balance is required when using copper and brass lighting fixtures in corrosive applications. If the water was allowed to remain in acid conditions, with chlorine or bromine present, copper corrosion occurs. Our laboratory testing concludes that chlorine/bromine does work better at a pH below 7.2. However, there are consequences that will result. Corrosion can present a problem below 7.0. As the pH falls below 7.2, chlorine/bromine can become increasingly more aggressive and irritating. Brass and copper fixtures will experience some natural patina. The fixture will turn a darker brown color as the patina process occurs.
Height: 5 1/2" (140mm)
Width: 6" (152mm)

Low Voltage Version shown above.

Hadco UW2100-N, UW2250-N Cast Bronze Low Voltage Niche Mounted Underwater Lights

UW2100-N 120V 100W T4*
Lamping: 100W T4 lamp is included with fixture. Electrical Assembly: Standard 10 ft. 16-3 AWG, 105° C, STOW water-resistant cord. Fixture is pre-wired and potted to prevent water entry. Mini-candelabra socket (E11).

UW2250-N 120V 250W T4*
Lamping: 250W maximum. 250W T4 lamp is included with fixture. Electrical Assembly: Standard 10 ft. 16-3 AWG, 105° C, STOW water-resistant cord. Fixture is pre-wired and potted to prevent water entry. Mini-candelabra socket (E11).

Housing: Spun stainless steel with cast nickel bronze trim. Stainless steel with integral bonding lugs and hub for connecting 1/2" or 3/4" conduit. Fasteners are 300 Series stainless steel. gasketing is silicone. Spun stainless steel. Rockguard is marine grade bronze. Integral and furnished as standard on all fixtures. This enables fixture to be used in accordance with NEC Article 680-51 in installations without an external low-water cutoff.
Finish: Natural Brass (N) is as-cast and tumble polished.
Optical Assembly: Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for wet locations. cETL listed to Canadian safety standards for wet locations. Manufactured to ISO 9001: 2000 Standards.
CORROSIVE CONDITIONS: Proper pH balance is required when using copper and brass lighting fixtures in corrosive applications. If the water was allowed to remain in acid conditions, with chlorine or bromine present, copper corrosion occurs. Our laboratory testing concludes that chlorine/bromine does work better at a pH below 7.2. However, there are consequences that will result. Corrosion can present a problem below 7.0. As the pH falls below 7.2, chlorine/bromine can become increasingly more aggressive and irritating. Brass and copper fixtures will experience some natural patina. The fixture will turn a darker brown color as the patina process occurs.
Height: 5 1/8" (130mm)
Width: 7 7/16" (189mm)

Low Voltage Version shown above.