Hadco Light Emitting Diode LED Landscaping Lights

RSC2 Louver Steplyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSC2 Louver Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSC2AK5D3E Louver Steplight with 3 LEDs
RSC2AL5D5E Louver Steplight with 5 LEDs

RSC2

• Input voltage range (VAC): 108-132
• 10.4 totals watts (3) 1W LEDs,
  13.5 total watts (5) 1W LEDs
• Type III Luxeon® white high output LEDs
• Integral Advance™ electronic LED driver

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.64 lb.

Hadco RSC2

Fasteners are 300 series stainless steel. Gasketing is silicone. Recessed housing contains four (4) 1/2 " NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion. Cast bronze fixture has polycarbonate, color impregnated, dark bronze finish. Die-cast copper-free aluminum with 45° cutoff, with frosted tempered glass. Cast bronze louver is natural cast bronze with frosted tempered glass. Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. Integral and furnished as standard on all fixtures. This enables fixture to be used in accordance with NEC Article 680-51 in installations without an external low-water cutoff.

Housing: Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications.  Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion.  Cast bronze fixture has polycarbonate, color impregnated, dark bronze finish.  Cast bronze louver is natural cast bronze with frosted tempered glass.  Die-cast copper-free aluminum with 45° cutoff, with frosted tempered glass.  Gasketing is silicone.  Fasteners are 300 series stainless steel.  Note: Recessed housing contains four (4) 1/2" NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. 

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Zinc-rich primer and thermoset powdercoat for durability. 

Optical Assembly: Symmetric reflector is precision formed, steel with a white reflective coating.  The cast louver offers lower light levels with cut-off for lighting stairways or general lighting where shielding of the light source is more important than high light levels. 

Lamping: 18W CFL (G24Q-2).  9W PLS Fluorescent (G23).  13W PLC Fluorescent (120V: GX23-2; 277V: G24Q-1).  Two 18W maximum S-8 (1141) lamps (Single contact bayonet base).  40W maximum T10 (4KV medium base porcelain socket).  Lower wattage lamps are acceptable. 

Electrical Assembly: Fixture is pre-wired with 18 AWG black, white, and ground wires. 1141 lamps use an integral 120V/12V transformer.

Ballast: The ballast for 18W CF shall be electronic 50 or 60Hz. The ballast for 9 and 13W CF shall be class B core and coil HPF rated for 0 degree starting temperature. 13W Fluorescent 120V: Core and coil, NPF, 0°C minimum start. 13W 277V: Electronic, 0°C minimum start.  9W Fluorescent ballast is core and coil, NPF, 0°C minimum start. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards.  ADA Compliant when used in indoor and outdoor wall applications. 

Height : 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.64 lb.

Optics: K5 Symmetric Optics

Wattage: F18 18W CF
8 (2) 18W 1141 (120/12) *1
F13 13W CFL
F9 9W CFL
I 40W T10

Voltage: E 120V or H 277V

Thermal Protection: P Thermal Protection Device *2

RSC2 Louver Steplyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSC2 Louver Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting with Warm Lens

RSC2AK5D3E Louver Steplight with 3 LEDs
RSC2AL5D5E Louver Steplight with 5 LEDs

RSC2 w/ Warm Lens

• Input voltage range (VAC): 108-132
• 10.4 totals watts (3) 1W LEDs,
  13.5 total watts (5) 1W LEDs
• Type III Luxeon® white high output LEDs
• Integral Advance™ electronic LED driver

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.64 lb.

Hadco RSC2 with Warm Lens

Housing: Cool external temperatures - all below 33;deg;C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85ºC for composite, 80°C for glass) and 4 seconds (74°C for composite, 70°C for glass) of contact.  Die-cast copper-free aluminum with 45° cutoff, with frosted tempered glass.  Cast bronze louver is natural cast bronze with frosted tempered glass.  Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion.  Cast bronze fixture has polycarbonate, color impregnated, dark bronze finish.  Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications.  Gasketing is silicone.  Fasteners are 300 series stainless steel.  Note: Recessed housing contains four (4) 1/2" NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. 

Finish: Zinc-rich primer and thermoset powdercoat for durability.  Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Optical Assembly: Warm (3000K), amber-colored tempered glass lens.  The cast louver offers lower light levels with cut-off for lighting stairways or general lighting where shielding of the light source is more important than high light levels.  Reflector is formed from highly reflective aluminum. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Pre-wired with high temperature 18 AWG wire.  Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards.  ADA Compliant when used in indoor and outdoor wall applications. 

Height : 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.64 lb.

Optics: K5 Symmetric Optics

Wattage: D3 3 1W LEDs
D5 5 1W LEDs

Lens: W Amber glass lens

Voltage: E 120V

RSF2 Flat Opal Lens Steplyte or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSF2 Flat Opal Lens Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSF2

• Input voltage range (VAC): 108-132
• 10.4 totals watts (3) 1W LEDs,
  13.5 total watts (5) 1W LEDs
• Type III Luxeon® white high output LEDs
• Integral Advance™ electronic LED driver

Select Finish: A Black or H Bronze
Optics: L5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.65 lb.

Hadco RSF2

Housing: Cool external temperatures - all below 32°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion.  Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. 

Finish: Zinc-rich primer and thermoset powdercoat for durability.  Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Finish: A Black, H Bronze

Optical Assembly: Opal Lens - made of UV stabilized injection molded polycarbonate.  Specular aluminum formed reflector. 

Optics: L5 Symmetric Optics

Wattage: D3 3 1W LEDs, D5 5 1W LEDs

Lens: W Amber glass lens

Voltage: E 120V

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Pre-wired with high temperature 18 AWG wire.  Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards.  ADA Compliant when used in indoor and outdoor wall applications. 

Height : 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.65 lb.

A= Black

H= Bronze

RSF2 Flat Opal Lens Steplyte or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSF2 Flat Opal Lens Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting with Warm Lens

RSF2AL5D3E Flat Opal Lens Steplight with 3 LEDs
RSF2AL5D5E Flat Opal Lens Steplight with 5 LEDs

RSF2 / RSFW2 with Warm Lens

• Input voltage range (VAC): 108-132
• 10.4 totals watts (3) 1W LEDs,
  13.5 total watts (5) 1W LEDs
• Type III Luxeon® white high output LEDs
• Integral Advance™ electronic LED driver

Select Finish: A Black or H Bronze
Optics: L5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.65 lb.

Hadco RSF2 with Warm Lens

Housing: Cool external temperatures - all below 33°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85°C for composite, 80°C for glass) and 4 seconds (74°C for composite, 70°C for glass) of contact.  Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion.  Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications. 

Finish: Zinc-rich primer and thermoset powdercoat for durability.  Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Finish: A Black, H Bronze

Optical Assembly: Opal Lens - made of UV stabilized injection molded polycarbonate.  Warm (3000K), amber-colored tempered glass interior lens.  Specular aluminum formed reflector. 

Optics: K5 Symmetric Optics

Wattage: D3 3 1W LEDs, D5 5 1W LEDs

Lens: W Amber glass lens

Voltage: E 120V

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Pre-wired with high temperature 18 AWG wire.  Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards.  ADA Compliant when used in indoor and outdoor wall applications.

Height : 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.65 lb.

A= Black

H= Bronze

RSS2 Internal Louver Steplight or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSS2 Internal Louver Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSS2AK5D3E Internal Louver Steplyte with 3 LEDs
RSS2AK5D5E Internal Louver Steplyte with 5 LEDs

RSS2

• Input voltage range (VAC): 108-132
• 10.4 totals watts (3) 1W LEDs,
  13.5 total watts (5) 1W LEDs
• Type III Luxeon® white high output LEDs
• Integral Advance™ electronic LED driver
  

Select Finish: A Black or H Bronze
Optics: K5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.75 lb.

Hadco RSS2

Housing: Cool external temperatures - all below 32°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications.  Gasketing is silicone.  Fasteners are 300 series stainless steel.  Note: Recessed housing contains four (4) 1/2" NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment.  Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion. 

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.   Zinc-rich primer and thermoset powdercoat for durability. 

Finish: A Black, H Bronze

Optical Assembly: Clear UV stabilized injection molded polycarbonate with 45° louvered screen insert.  Specular aluminum formed reflector. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: 4Pre-wired with high temperature 18 AWG wire.  Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs.  Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards.  ADA Compliant when used in indoor and outdoor wall applications. 

Height : 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.75 lb.

Optics: K5 Symmetric Optics

Wattage: D3 3 1W LEDs, D5 5 1W LEDs

Voltage: E 120V

RSS2 Internal Louver Steplight or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSS2 Internal Louver Steplyte or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSS2AK5D3E Internal Louver Steplyte with 3 LEDs
RSS2AK5D5E Internal Louver Steplyte with 5 LEDs

RSS2 with Warm Lens

• Input voltage range (VAC): 108-132
• 10.4 totals watts (3) 1W LEDs,
  13.5 total watts (5) 1W LEDs
• Type III Luxeon® white high output LEDs
• Integral Advance™ electronic LED driver
  

Select Finish: A Black or H Bronze
Optics: K5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.75 lb.

Hadco RSS2 with Warm Lens

Housing: Cool external temperatures - all below 33°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85°C for composite, 80°C for glass) and 4 seconds (74°C for composite, 70°C for glass) of contact.  Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications.  Gasketing is silicone.  Fasteners are 300 series stainless steel.  Note: Recessed housing contains four (4) 1/2" NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment.  Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion. 

Finish: Zinc-rich primer and thermoset powdercoat for durability.  Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.  

Finish: A Black, H Bronze

Optical Assembly: Clear UV stabilized injection molded polycarbonate with 45° louvered screen insert.  Warm (3000K), amber-colored tempered glass interior lens.  Specular aluminum formed reflector. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Pre-wired with high temperature 18 AWG wire.  Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards.  ADA Compliant when used in indoor and outdoor wall applications. 

Height : 3 1/2" (90mm)
Width: 9" (229mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.75 lb.

Optics: K5 Symmetric Optics

Lens: W Amber glass lens

Wattage: D3 3 1W LEDs, D5 5 1W LEDs

Voltage: E 120V

RSV2 Vertical Louver Steplight or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSV2 Vertical Louver Steplight or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSV2AK5D3E Vertical Louver Steplight with 3 LEDs
RSV2AK5D5E Vertical Louver Steplight with 5 LEDs

RSV2 / RSV2 w/ Warm Lens

• Input voltage range (VAC): 108-132
• 10.4 totals watts (3) 1W LEDs,
  13.5 total watts (5) 1W LEDs
• Type III Luxeon® white high output LEDs
• Integral Advance™ electronic LED driver

Select Finish: A Black. B White. H Bronze or N Natural Brass
Select Optics: K5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 8 3/4" (222mm)
Width: 3 1/4" (83mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.6 lb.

Hadco RSV2

Housing: Cool external temperatures - all below 32°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  Note: Recessed housing contains four (4) 1/2" NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment.  Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications.  Fasteners are 300 series stainless steel.  Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion.  Cast bronze fixture has polycarbonate, color impregnated, dark bronze finish.  Die-cast copper-free aluminum with 45° cutoff, with frosted tempered glass.  Cast bronze louver is natural cast bronze with frosted tempered glass.  Gasketing is silicone. 

Finish: Zinc-rich primer and thermoset powdercoat for durability.  Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.  

Optical Assembly: The cast louver offers lower light levels with cut-off for lighting stairways or general lighting where shielding of the light source is more important than high light levels.  Reflector is formed from highly reflective aluminum. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Pre-wired with high temperature 18 AWG wire.  Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. 

Warranty: Three-year limited warranty.

Certification: UUL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards.  ADA Compliant when used in indoor and outdoor wall applications. 

Height : 8 3/4" (222mm)
Width: 3 1/4" (83mm)
Depth: 3 1/2" (90mm)

Optics: K5 Symmetric Optics

Wattage: D3 3 1W LEDs, D5 5 1W LEDs

Lens: W Amber glass lens

Voltage: E 120V

RSV2 Vertical Louver Steplight or Bricklyte
Line Voltage LED Landscape Step and Deck Lighting

Hadco RSV2 Vertical Louver Steplight or Bricklyte
Line Voltage Landscape Step and Deck Lighting

RSV2AK5D3E Vertical Louver Steplight with 3 LEDs
RSV2AK5D5E Vertical Louver Steplight with 5 LEDs

RSV2 / RSV2 w/ Warm Lens

• Input voltage range (VAC): 108-132
• 10.4 totals watts (3) 1W LEDs,
  13.5 total watts (5) 1W LEDs
• Type III Luxeon® white high output LEDs
• Integral Advance™ electronic LED driver

Select Finish: A Black. B White. H Bronze or N Natural Brass
Select Optics: K5 Symmetric Optics only
Select Wattage: D3 3 x 1W LEDs or D5 5 x 1W LEDs

Height: 8 3/4" (222mm)
Width: 3 1/4" (83mm)
Depth: 3 1/2" (90mm)
Max. Weight: 3.6 lb.

Hadco RSV2 with Warm Lens

Housing: Cool external temperatures - all below 33°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85°C for composite, 80°C for glass) and 4 seconds (74°C for composite, 70°C for glass) of contact.  Die-cast copper-free aluminum with 45° cutoff, with frosted tempered glass.  Cast bronze louver is natural cast bronze with frosted tempered glass.  Die-cast aluminum trim ring contains less than 0.3% copper to resist corrosion.  Cast bronze fixture has polycarbonate, color impregnated, dark bronze finish.  Die-cast aluminum back box contains less than 0.3% copper to prevent corrosion in concrete or masonry applications.  Gasketing is silicone.  Fasteners are 300 series stainless steel.  Note: Recessed housing contains four (4) 1/2" NPS conduit inlets (two (2) on bottom and one on each side) and internal pull-through wiring compartment. 

Finish: Zinc-rich primer and thermoset powdercoat for durability.  Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.  

Optical Assembly: The cast louver offers lower light levels with cut-off for lighting stairways or general lighting where shielding of the light source is more important than high light levels.  Reflector is formed from highly reflective aluminum.  Warm (3000K), amber-colored tempered glass lens. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Pre-wired with high temperature 18 AWG wire.  Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. 

Warranty: Three-year limited warranty.

Certification: UUL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards.  ADA Compliant when used in indoor and outdoor wall applications. 

Height : 8 3/4" (222mm)
Width: 3 1/4" (83mm)
Depth: 3 1/2" (90mm)

Optics: K5 Symmetric Optics

Wattage: D3 3 1W LEDs, D5 5 1W LEDs

Lens: W Amber glass lens

Voltage: E 120V

LED Housing Only LED Housing Only (RS2D-_HO)

Hadco RS2D-_HO LED Housing Only for Steplight or Bricklyte

RS2D-AHO LED Housing Only for Pre-Shipment, A Black
RS2D-BHO LED Housing Only for Pre-Shipment, B White
RS2D-HHO LED Housing Only for Pre-Shipment, H Bronze
RS2D-NHO LED Housing Only for Pre-Shipment, N Natural Brass

LED housing only. When housing only is ordered for pre-shipment, add suffix "LH" (Less Housing) to complete catalog number to fixture without housing.

Select Finish: A Black. B White. H Bronze or N Natural Brass

LED Underwater Light (ULW5D4)
Specialty Low Voltage Landscape Light

Hadco LED Underwater Light (ULW5D4) LED Pond Light
Specialty Low Voltage Landscape Light

ULW5D4-H LED Ultem Underwater

ULW5D4

• Input voltage range (VAC): 10.5-17
• 12.4 total watts
• Four (4) Type III Luxeon® high output LEDs
• Integral voltage regulator, suitable for standard remote transformers

Finish: H Bronze only

Height: 6 11/16" (170mm)
Width: 4 1/16" (103mm)
Max. Weight: 5.04 lb.

Hadco ULW5D4

One-piece injection molded ULTEM® High Performance Polymer composite. Lens ring is a Single-piece injection molded ULTEM® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance. Fasteners are 300 series stainless steel.

Housing: Cool external temperatures - all below 31°C when underwater - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85°C for composite, 80°C for glass) and 4 seconds (74°C for composite, 70°C for glass) of contact.  One-piece injection molded ULTEM® High Performance Polymer composite.  Lens ring is a Single-piece injection molded ULTEM® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance.  Fasteners are 300 series stainless steel. 

Finish: Composite is textured, pressure formed, molded-in-color. 
H Bronze only

Optical Assembly: Integral collimating flood (25°) optics.  Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Standard 10 ft. 18-2, 105° C, STWA water-resistant cord. Fixture is prewired and potted to prevent water entry.  Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts.   12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards. 

IP Rating: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).

Height : 6 11/16" (170mm)
Width: 4 1/16" (103mm)
Max. Weight: 5.04 lb.

LED Underwater Light (ULW5D4)
Specialty Low Voltage Landscape Light

Hadco LED Underwater Light (ULW5D4) LED Pond Light with Warm Lens
Specialty Low Voltage Landscape Light

ULW5D4-H LED Ultem Underwater

ULW5D4 with Warm Lens

• Input voltage range (VAC): 10.5-17
• 12.4 total watts
• 25° flood optics
• Four (4) Type III Luxeon® high output LEDs
• Integral voltage regulator, suitable for standard remote transformers

Finish: H Bronze only

Height: 6 11/16" (170mm)
Width: 4 1/16" (103mm)
Max. Weight: 5.04 lb.

Hadco ULW5D4

Housing: Cool external temperatures - all below 36°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  One-piece injection molded ULTEM® High Performance Polymer composite.  Lens ring is a Single-piece injection molded ULTEM® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance.  Fasteners are 300 series stainless steel. 

Finish: Composite is textured, pressure formed, molded-in-color. 
H Bronze only

Optical Assembly: Warm (3000K), amber-colored tempered glass lens.  Integral collimating flood (25°) optics. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Standard 10 ft. 18-2, 105° C, STWA water-resistant cord. Fixture is prewired and potted to prevent water entry.  Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts.   12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards. 

IP Rating: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).  

Height : 6 11/16" (170mm)
Width: 4 1/16" (103mm)
Max. Weight: 5.04 lb.

Hadco LED Inground ILN5D4 & ILW5D4 Spot or Flood Landscape Lighting

ILN5D4-H LED Ultem Inground - Spot
ILW5D4-H LED Ultem Inground - Flood

ILN5D4 / ILW5D4 with Warm Lens

• Input voltage range (VAC): 10.5-17
• 12.4 total watts
• Four (4) Type III Luxeon® high output LEDs
• Integral voltage regulator, suitable for standard remote transformers

Housing: Cool external temperatures - all below 38°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85°C for composite, 80°C for glass) and 4 seconds (74°C for composite, 70°C for glass) of contact.  One-piece injection molded ULTEM® High Performance Polymer composite.  Lens ring is a Single-piece injection molded ULTEM® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance.  Fasteners are 300 series stainless steel. 

Finish: Composite is textured, pressure formed, molded-in-color. 

Height: 4 3/8" (111mm)
Width: 4 1/8" (105mm)
Max. Weight: 1.24 lb.

Hadco ILN5D4 & ILW5D4

Optical Assembly: Integral collimating flood (25°) optics.  Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Low voltage transformer must be ordered to power the fixtures.  Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts. 12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.  12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty.

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards. 

IP Rating: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).  

Height : 4 3/8" (111mm)
Width: 4 1/8" (105mm)
Max. Weight: 1.24 lb.

Finish: H Bronze

Hadco LED Inground ILN5DW4 & ILW5DW4 Spot or Flood Landscape Lighting

ILN5D4 / ILW5D4 with Warm Lens

• Input voltage range (VAC): 10.5-17
• 12.4 total watts
• Four (4) Type III Luxeon® high output LEDs
• Integral voltage regulator, suitable for standard remote transformers

Housing: Cool external temperatures - all below 42°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85°C for composite, 80°C for glass) and 4 seconds (74°C for composite, 70°C for glass) of contact.  One-piece injection molded ULTEM® High Performance Polymer composite.  Lens ring is a Single-piece injection molded ULTEM® High Performance Polymer with gasketed lens. Twist-off operation for ease of maintenance.  Gasketing is silicone.  Fasteners are 300 series stainless steel. 

Finish: Composite is textured, pressure formed, molded-in-color. 

Height: 4 3/8" (111mm)
Width: 4 1/8" (105mm)
Max. Weight: 1.24 lb.

Hadco ILN5D4 & ILW5D4

Optical Assembly: Integral collimating flood (25°) optics.  Clear convex lens, high temperature glass furnished with silicone O-ring for watertight seal. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Low voltage transformer must be ordered to power the fixtures.  Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts.   12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire.   Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.  12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty.

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards. 

IP Rating: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).  

Height : 4 3/8" (111mm)
Width: 4 1/8" (105mm)
Max. Weight: 1.24 lb.

Finish: H Bronze

Hadco LED Inground LED Inground Flood Optic (I25) Narrow Spot, Spot or Flood Landscape Lighting

Inground Flood Optic I25 Narrow Spot, Spot or Flood Landscape Lighting

• 39 watt MH equivelent
• Smart Select electronic driver
• Input voltage range (VAC) 120-277
  50-60hz
  auto sensing

The revolutionary i2.5 composite inground provides optimum performance in a small aperture luminaire. Patented design elements including a hinged lens ring, potted factory seal, cool lens option and only 2 screws that do not require a torque wrench - the i2.5 reinforces HADCO's position as the leader in landscape lighting. Now available with LED.

LED Specifications: Minimum 70 color rendering index (CRI).  Approximately 50,000 hours of operational life (at 25 C ambient temperature and 70% lumen maitenance). 

Housing: Single-piece compression molded fiberglass reinforced polyester composite, factory pressure tested to ensure water will not wick or leak through.   Separate sealed compartments provide isolation between field wiring, optics, and ballast (MH and CFL).  Isolated, grade-mounted sealed wiring compartment with two (2) 3/4" threaded conduit inlets in bottom for feed-through wiring capabilities and supplied with gel-filled wire nuts.   Cast cover to match trim ring with two captive stainless steel slotted Phillips machine screws for access.   Potted factory seal with anti-wicking wiring between grade-level junction compartment and ballast compartment. Isolated ballast compartment with key-slotted, silicone-gasket cover.   Rock guard made of cast brass (natural finish) or cast stainless steel (satin finish).   Ring is factory pre-drilled for optional guard.   Trim ring is natural cast bronze or cast stainless steel.  Lens ring is hinged with two captive stainless slotted Phillips machine screws for access to lamping compartment (tamper-resistant screws available upon request.)  Half dome 360 degree field adjustable for glare control, constructed of natural cast brass (natural finish) or cast stainless steel (satin finish) to match lens ring.  Both options are designed to mount utilizing factory pre-drilled holes on lens ring with water channel to allow lens to stay free of dirt and contamination build-up. 

Finish: Natural Brass has satin matte finish.  Stainless Steel has satin matte finish. 

Hadco ILN5D4 & ILW5D4

Optical Assembly:Clear, flat, molded borosilicate glass, high impact, 3000 lb. live load rated, drive-over glass, with molded 100% silicone gasket, factory adheared.   Optional lens assemblies include cool touch lens, reducing lens temperatures by 35%, ice blue lens, linear or multi-directional spread lens.   Sealed optical chamber.  Aiming 15° either side of vertical and full 360° rotation. Angle degree marks for precise vertical aiming with tool-less LOC-AIM®.  Handle enables easy tool-less removal of optical assembly for hot aiming and re-lamping, simply press-fit back into place. 

LED Color/Lumens:
WL34 Warm White, 342 Lumens *1
CL53 Cool White, 525 Lumens *1
*1 Smart Select Electronic Driver: 120-277VAC 50/60 Hz auto-sensing

Electrical Assembly: Smart Select Electronic Driver 120 to277 VAC input; 50-60Hz; auto-sensing.  Operating temperature range -40 C (-40 F) to +25 C (+77 F)  17watts consumed (total fixture consumption)  

Warranty: Ten-year limited warranty. 

Certification: Manufactured to ISO 9001:2000 Standards.  ADA compliant when used in concrete and flush mounted with CPS25.  ETL Listed to U.S. safety standards for wet locations.  cETL listed to Canadian safety standards for wet location 

IP Rating: IP66/68: Dust-tight and dual rated - sealed against direct jets of water and against temporary immersion at a depth greater than 1 meter (3.28 feet).  

Height : 15 3/4
Width: 7 1/2
Depth: 9 3/4

Finish: SS Stainless steel (Matte), H Bronze

Hadco LED Bullyte BLN5D4 & BLW5D4 Spots & Flood Die-cast marine grade aluminum alloy bullet landscape lighting

Narrow
BLN5D4-A LED Bullyte - Spot
BLN5D4-H LED Bullyte - Spot

Wide
BLW5D4-A LED Bullyte - Flood
BLW5D4-H LED Bullyte - Flood

BLN5D4 / BLW5D4 with Warm Lens

• Input voltage range (VAC): 10.5-17
• 12.4 total watts
• Four (4) Type III Luxeon® high output LEDs
• Integral voltage regulator, suitable for standard remote transformers

Housing: Cool external temperatures - all below 46°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  Die-cast marine grade aluminum alloy.  Fully rotatable shroud, double gasketed, die-cast marine grade alloy aluminum.  Fully-adjustable swivel arm with vibration-proof locking teeth.  1/2" NPS male threads to screw on to accessory mounting stake or junction box, sold separately.  Fasteners are 300 series stainless steel.  Gasketing is silicone. 

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.  

Optical Assembly: Integral collimating flood (25°) optics.  Clear tempered glass affixed at 10° angle for natural cleaning. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Low voltage transformer must be ordered to power the fixtures.  Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts.   12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire.   Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.  12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards. 

IP Rating: IP66: Dust-tight and sealed against direct jets of water.
Height : 2 3/8" (60mm)
Width: 2 13/16" (71mm)
Length: 5 13/16" (147mm)
Max. Weight: 2.6 lb.

Finish: A Black, H Bronze

Hadco LED Bullyte BLN5DW4 & BLW5DW4 Spots & Flood Die-cast marine grade aluminum alloy bullet landscape lighting

Narrow
BLN5DW4-A LED Bullyte - Spot
BLN5DW4-H LED Bullyte - Spot

Wide
BLW5DW4-A LED Bullyte - Flood
BLW5DW4-H LED Bullyte - Flood

BLN5DW4 / BLW5DW4 with Warm Lens

• Input voltage range (VAC): 10.5-17
• 12.4 total watts
• Four (4) Type III Luxeon® high output LEDs
• Integral voltage regulator, suitable for standard remote transformers

Housing: Cool external temperatures - all below 48°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (85°C for composite, 80°C for glass) and 4 seconds (74°C for composite, 70°C for glass) of contact.  Die-cast marine grade aluminum alloy.  Fully rotatable shroud, double gasketed, die-cast marine grade alloy aluminum.  Fully-adjustable swivel arm with vibration-proof locking teeth.  1/2" NPS male threads to screw on to accessory mounting stake or junction box, sold separately.  Fasteners are 300 series stainless steel.  Gasketing is silicone. 

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.  

Optical Assembly: Warm (3000K), amber-colored tempered glass lens, affixed at a 10° for natural cleaning.  Integral collimating spot (12°) optics. 

Lamping: Type III Luxeon® white high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal). 

Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 12.4 total watts.   12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire.   Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.  12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty. 

Certification: UL Listed to U.S. safety standards for wet locations.  cUL Listed to Canadian safety standards for wet locations.  Manufactured to ISO 9001:2000 Standards. 

IP Rating: IP66: Dust-tight and sealed against direct jets of water. 
Height : 2 3/8" (60mm)
Width: 2 13/16" (71mm)
Length: 5 13/16" (147mm)
Max. Weight: 2.6 lb.

Finish: A Black, H Bronze

Hadco LED Pathlyte (TRL4DW3)

CL2D2-A LED Contemporary Pathlight
CL2D2-H LED Contemporary Pathlight

CL2D2 / CL2DW2

• Input voltage range (VAC): 10.5-17
• 6.5 watts
• Philips LumiLED Rebels
• Integral voltage regulator, suitable for standard remote transformers

Housing: Cool external temperatures - all below 43°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  Die-cast aluminum.  Stem is extruded aluminum.  1/2" NPS male threads to screw on to accessory mounting stake or junction box, sold separately.  Fasteners are 300 series stainless steel. 

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.

Optical Assembly: Sealed collimating optics with diffuser lens for even light distribution.

Lamping: Philips Lumiled Rebel, Cool White (6,000K)  

Electrical Assembly: Input voltage range (VAC): 10.8 - 17.5. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 12 volts, 9.3 total watts.  Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature.  Low voltage transformer must be ordered to power the fixtures.  12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire.   Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.  12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty. 

Certification: ETL Listed to U.S. safety standards for wet locations.  cETL listed to Canadian safety standards for wet location  Manufactured to ISO 9001:2000 Standards. 

Height : 23 7/16" (597mm)
Width: 8 5/16" (211mm)
Max. Weight: 1.9 lb.

Finish: G Verde, OM Old Marble, T Speckled Stone, U Sienna

Hadco LED Pathlyte (CL2D2)

CL2D2-A LED Contemporary Pathlight
CL2D2-H LED Contemporary Pathlight

Housing: Cool external temperatures - all below 36°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  Die-cast aluminum.  Gasketed twist lock top.  Stem is extruded aluminum.  1/2" NPS male threads to screw on to accessory mounting stake or junction box, sold separately. 

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.  

Optical Assembly: Clear tempered flat glass lens. 

Lamping: Philips Lumiled Rebel, Cool White (6,000K)  

Electrical Assembly: OptoElectronix electronic LED driver. UL Class 2 -10°C to 50°C mimum starting temperature. Internal surge protector built into LED driver circuit  Input voltage range (VAC): 10.8 - 17.0.  6.5 total watts consumed.  Connects directly to 12V AC or 12V DC power source.  Low voltage transformer must be ordered to power the fixtures.  12 Volt system requires remote transformer, not included.  Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.  12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire.  

Warranty: Three-year limited warranty. 

Certification: ETL Listed to U.S. safety standards for wet locations.  cETL listed to Canadian safety standards for wet location  Manufactured to ISO 9001:2000 Standards. 

Height : 21" (533mm)
Width: 4 3/4" (121mm)
Max. Weight: 2.5 lb.

Finish: A Black, H Bronze

Hadco LED Pathlyte (RL4D3)

RL4D3-A LED Horizon Pathlight

RL4D3 / RL4DW3

• Input voltage range (VAC): 10.5-17
• 6.5 watts
• Philips LumiLED Rebels
• Integral voltage regulator, suitable for standard remote transformers

Housing: Cool external temperatures - all below 40°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  Die-cast aluminum.  Stem is extruded aluminum.  1/2" NPS male threads to screw on to accessory mounting stake or junction box, sold separately.  Fasteners are 300 series stainless steel.  Gasketing is silicone. 

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.  

Optical Assembly: Frosted tempered glass lens.  Spun aluminum reflector with white thermoset powdercoat. 

Lamping: Philips Lumiled Rebel, Warm White (3,000K) 

Electrical Assembly: Low voltage transformer must be ordered to power the fixtures.  Input voltage range (VAC): 10.8 - 17.0.  6.5 total watts consumed.  OptoElectronix electronic LED driver. UL Class 2 -10°C to 50°C mimum starting temperature. Internal surge protector built into LED driver circuit  Connects directly to 12V AC or 12V DC power source.  12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire.   Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.  12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty. 

Certification: ETL Listed to U.S. safety standards for wet locations.  cETL listed to Canadian safety standards for wet location  Manufactured to ISO 9001:2000 Standards. 

IP Rating: IP66: Dust-tight and sealed against direct jets of water. 

Height : 17 1/4" (435mm)
Width: 10" (253mm)
Max. Weight: 3.18 lb.

Finish: A Black

Hadco LED Pathlyte (ML4D3)

ML4D3-A LED Mushroom
ML4D3-G LED Mushroom
ML4D3-H LED Mushroom

ML4D3 / ML4DW3

• Input voltage range (VAC): 10.5-17
• 6.5 watts
• Philips LumiLED Rebels
• Integral voltage regulator, suitable for standard remote transformers

IP Rating: IP66: Dust-tight and sealed against direct jets of water. 

Housing: Cool external temperatures - all below 43°C - so the luminaire is cool to the touch, including the lens. Perfect for high pedestrian traffic and plant life applications. Exceeds European standard EN 563 both 1 second (74°C for coated metal, 80°C for glass) and 4 seconds (61°C for coated metal, 70°C for glass) of contact.  Die-cast aluminum.  Stem is extruded aluminum.  1/2" NPS male threads to screw on to accessory mounting stake or junction box, sold separately.  Fasteners are 300 series stainless steel. 

Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting.  Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications.  

Optical Assembly: Sealed collimating optics with diffuser lens for even light distribution.

Lamping: Philips Lumiled Rebel, Cool White (6,000K)  

Electrical Assembly: OptoElectronix electronic LED driver. UL Class 2 -10°C to 50°C mimum starting temperature. Internal surge protector built into LED driver circuit  Input voltage range (VAC): 10.8 - 17.0.  6.5 total watts consumed.  Connects directly to 12V AC or 12V DC power source.  Low voltage transformer must be ordered to power the fixtures.  12 Volt fixture is pre-wired with 3-ft pigtail of 18-2 AWG, 105° C, SPT-1 wire.   Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.  12 Volt system requires remote transformer, not included. 

Warranty: Three-year limited warranty. 

Certification: ETL Listed to U.S. safety standards for wet locations.  cETL listed to Canadian safety standards for wet location  Manufactured to ISO 9001:2000 Standards. 

Height : 19 1/2" (495mm)
Width: 5 1/16" (129mm)
Max. Weight: 1.9 lb.

Finish: A Black, H Bronze, G Verde