Housing– Single-piece PVC tube allows easy installation
and
water to run through when installed on drainage material
(gravel to be supplied by installer). Straight cut end
allows flush ground mounting, and an accessory lens
guard (IL3H) or rock guard (IG3H or IG30H) may be ordered
separately, but is not required. Angled cut end requires
the top three inches installed above ground for maximum
vertical spot aiming with shielding being provided on
three sides.
Lamp Holder (Patented)– Durable silicone rubber
lamp holder has integral fins to allow the height and
angle of the lamp to be adjusted without any mechanical
moving parts. Fixture
offers 360° lamp rotation and up to 45° off
vertical aiming adjustability, restricted only by the
cut-off of the housing.
finish– Black silicone lampholder with black PVC
sleeve.
Lens– Optional lens available, see below.
Socket– Double screw terminal.
Wiring– 4-ft. of 18-2 low voltage cable with a
low voltage quick
connector on one end for easy energizing to the low
voltage
supply cable. Two spade connectors are provided on the
other
end for easy lamp installation. One foot of the 18-2
cable should be left as slack inside the PVC housing
to allow easy lamp adjustment or removal.
IG3H Rockguard Bronze
IG30H Rockguard Bronze
IL3H Lens guard Bronze
Above accessories to be used with
straight cut end only.
Hadco
I3 Composite Inground Lighting
I3G-H Bronze with Guard
I3-H Bronze
120 Volt
100 watt maximum
PAR/R30 & PAR38 Lamps
Housing– Single-piece compression
molded fiberglass
reinforced polyester composite housing,
lens ring and rock
guard with stainless steel fasteners.
finish– Color impregnated bronze composite.
Lens– Convex lens is clear, high temperature
tempered glass
furnished with silicone molded gasket for
watertight seal.
Socket– Porcelain medium base.
Wiring– Pre-wired with high temperature
#18 wire.
Aiming– Lamps have 358° rotation
and 15° off vertical
adjustability.
UL, cUL Listed.
Hadco
LED Inground ILN5D4 & ILW5D4 Spot or
Flood Landscape Lighting
ILN5D4-H LED Ultem Inground - Spot
ILW5D4-H LED Ultem Inground - Flood
Housing: One-piece injection molded ULTEM®
High Performance Polymer composite. Lens
ring is a Single-piece injection molded
ULTEM® High Performance Polymer with
gasketed lens. Twist-off operation for ease
of maintenance. Fasteners are 300 series
stainless steel.
Finish: Composite is textured, pressure
formed, molded-in-color.
Optical Assembly: Integral collimating
flood (25°) optics. Clear convex lens,
high temperature glass furnished with silicone
O-ring for watertight seal.
Lamping: Type 3 Luxeon® high-output
LEDs powered at 700mA to operate for 50,000
hours.
Electrical Assembly: Input voltage range
(VAC): 10.8 - 17.5. Input frequency: 60Hz.
Integral surge protector built into LED
driver circuit. 12 volts, 12.4 total watts.
12 Volt fixture is pre-wired with 3-ft pigtail
of 18-2 AWG, 105° C, SPT-1 wire. Low
voltage quick connector, catalog #LVC3 included
for easy hook-up to the low voltage supply
cable, not included. 12 Volt system requires
remote transformer, not included.
Warranty: Three-year limited warranty.
Certification: UL Listed to U.S. safety
standards for wet locations. cUL Listed
to Canadian safety standards for wet locations.
Manufactured to ISO 9001:2000 Standards.
IP Rating: IP66/68 to 1M (3.28FT): Dust-tight
and dual rated - sealed against direct jets
of water and against continuous immersion
up to a depth of 1 meter (3.28 feet).
Finish: H Bronze
H= Bronze
1/2" N.P.S. conduit inlets on bottom.
Hadco
I2 Composite Inground Light
I2G-H Bronze with Guard
I2-H Bronze
120 Volt
100 watt maximum
PAR/R30 or PAR/R20 Lamp
IM2G-H50 Bronze
120 Volt
With rock guard
Mercury Vapor
50 MV watt maximum
HR20 Lamp
Housing– Single-piece compression
molded fiberglass reinforced polyester composite
housing, lens ring and rock guard with stainless
steel fasteners.
finish– Color impregnated bronze composite.
Lens– Convex lens is clear, high temperature
tempered glass furnished with silicone molded
gasket for watertight seal.
Socket– Porcelain medium base.
Wiring– Pre-wired with high temperature
#18 wire.
Ballast– IM2 standard 120 volt core
and coil HPF.
UL, cUL Listed.
Hadco
I4 Composite 120 Volt Inground Landscape
Light
I4G-H Bronze with Guard
I4-H Bronze
120 Volt
150 watt maximum
PAR38/R40 Lamp
Housing– Single-piece compression
molded fiberglass reinforced polyester composite
housing, lens ring and rock guard with stainless
steel fasteners.
finish– Color impregnated bronze composite.
Lens– Convex lens is clear, high temperature
tempered glass furnished with silicone molded
gasket for watertight seal.
Socket– Porcelain medium base.
Wiring– Pre-wired with high temperature
#18 wire.
Aiming– Lamps have 358° rotation
and 15° off vertical adjustability.
The following are basic steps
in installing inground fixtures into soil.
For detailed instructions, refer to the installation
sheet enclosed with each fixture.
1. Excavate soil for fixture placement
and conduit runs. Allow a minimum of 3"
around and under housing for drainage material.
2. Remove the screws from the glass/gasket
assembly and wiring compartment cover. Connect
conduit fittings to housing conduit entries
utilizing a thread sealant, and tighten
to 40 ft-lbs. max. DO NOT REMOVE the moisture
absorbing desi-pak from inside the fixture.
3. Connect 120V leads in wiring compartment
to supply wires. Make ground connection.
The contractor must pull ground wire or
make a ground connection to the metal conduit
system.
4. Conduit entries must be potted to prevent
water entry (3M 4442 GELA supplied with
I3 and I4). Replace the wiring compartment
cover.
5. Install the ballast tray. Plug lamping
module into quick connect, if applicable.
6. Install the correct lamp. DO NOT EXCEED
the maximum wattage marked on the fixture.
7. Clean gasket seating surfaces. Screw
holes can be blown clear or cleared with
a #10-24 tap. Insert screws through lid
and tighten using an alternating torque
sequence to 20 (min.) 30 (max.) inch-lbs.
8. Fixture housing should be surrounded
by a 3" (minimum) layer of sand or
gravel to ensure drainage. Materials such
as vermiculite and bark are for ground cover
only. Full depths of these may cause overheating.
In concrete pour cases, the housing is placed
on a 4" (minimum) bed of gravel, with
soil below. Do not install fixtures where
water collects arid stands for any length
of time.
finishes and Materials
Hadco makes it easier than ever to select
the right color for your exquisite landscape
design with a full palette of colors and
textures. Expand your design capabilities
with new finishes that are sure to compliment
your commercial or residential landscape
lighting needs.
For an aged appearance, Oiled and Verde
Brass materials have been added to the NightLife
fixture choices for a step back in time.
And for more earthy settings, there is
the Speckled Stone finish, which is at home
among foliage as well as any number of masonry
materials.
To Order:
