 |
Hadco Low Voltage & Line
Voltage Composite BrickLytes
 12
Volt, 120 Volt CB100 Composite
Housing: Die-cast aluminum back box contains less than
0.3% copper to prevent corrosion in concrete or masonry
applications. Horizontal Louver Faceplate is an injection
molded RYTON® composite with frosted tempered glass and
stainless steel screws.
Finish: Zinc-rich primer and thermoset powdercoat for durability.
Composite is textured, pressure formed, molded-in-color.
Finish: A Black, H Bronze
Optical Assembly: Horizontal Louver Faceplate - Injection
molded RYTON® composite with frosted tempered glass, with
stainless steel screws.
12 Volt Lamping: Two 18W maximum S-8 (1141) lamps (Single contact bayonet base).
120 Volt Lamping: Two 18W maximum S-8 (1141) lamps
(Single contact bayonet base).
12 Volt Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is pre-wired with 6-ft. Pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector, catalog #LVC3 included for easy hook-up to the low voltage supply cable, not included.
120 Volt Electrical Assembly: Single contact bayonet
(S-8). 12 volt fixture is pre-wired with 6-ft. Pigtail
of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector,
catalog #LVC3 included for easy hook-up to the low voltage
supply cable, not included.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety standards for
wet locations. cETL listed to Canadian safety standards
for wet locations. Manufactured to ISO 9001:2008 Standards.
ADA Compliant when used in indoor and outdoor wall applications.
Hadco
BrickLytes (Brick Lights) > |
|
| |
Hadco Low Voltage, Line Voltage
& LED Polycarbonate BrickLytes
Housing:
Die-cast aluminum faceplate with galvanized
steel, single gang recessed box with stainless
steel fasteners. Die-cast aluminum back box
contains less than 0.3% copper to prevent
corrosion in concrete or masonry applications.
Gasketing is silicone. Fasteners are 300
Series stainless steel. Note: Recessed housing
contains four (4) ½" NPS conduit inlets
(two (2) on bottom and one on each side)
and internal pull-through wiring compartment.
Die-cast aluminum trim ring contains less
than 0.3% copper to resist corrosion.
Finish: Thermoset polyester powdercoat is electrostatically applied after a five-stage conversion cleaning process and bonded by heat fusion thermosetting. Laboratory tested for superior weatherability and fade resistance in accordance with ASTM B-117-64 and ANSI/ASTM G53-77 specifications. Zinc-rich primer and thermoset powdercoat for durability.
12 Volt
Electrical Assembly: Single contact bayonet
(S-8). 12 volt fixture is pre-wired with
6-ft. Pigtail of 18-2 AWG, 105° C, SPT-1W
wire. Low voltage quick connector, catalog
#LVC3 included for easy hook-up to the low
voltage supply cable, not included.
Finish: A Black, H Bronze
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG black, white and ground wires.
WARRANTY: Three-year limited warranty. LED WARRANTY: Five-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety
standards for wet locations. cETL listed
to Canadian safety standards for wet locations.
Manufactured to ISO 9001:2008 Standards.
ADA Compliant when used in indoor and outdoor
wall applications.
ADA Compliant – Compliant when used in indoor and outdoor wall applications.
ETL, cETL Listed.
Hadco
BrickLytes (Brick Lights) > |
 |
120
Volt RSS2, RSS2 LED Polycarbonate
Optical Assembly: Specular aluminum formed
reflector. Clear UV stabilized injection
molded polycarbonate with 45 degree louvered
screen insert.
Lamping: 18W CFL (G24Q-2). 13W CFL (GX23D-2).
40W maximum T10 (4KV medium base porcelain
socket). Lower wattage lamps are acceptable. LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at 50,000 hours. Cool white (5500K nominal).
Electrical Assembly: 4kv rated medium base
porcelain socket. Nickel-plated screw shell
with center contact. 18W Fluorescent is
a GX24q-2 socket.
LED Electrical Assembly: Pre-wired with high temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency: 60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts (3) 1W LEDs, 13.5 total watts (5) 1W LEDs. Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature. |
 |
12
Volt RSBL2, 120 Volt RSB2 Polycarbonate
Optical Assembly: UV stabilized, injection
molded polycarbonate bubble faceplate, reinforced
with frosted tempered glass, with stainless
steel screws.
12 Volt Lamping: 20W maximum T3 bi-pin lamp.
120 Volt Lamping: 13W PLC Fluorescent (120V:
GX23-2; 277V: G24Q-1). 18W CFL (G24Q-2).
40W maximum T10 (4KV medium base porcelain
socket). Lower wattage lamps are acceptable.
Lamp is not included. |
 |
12
Volt RSFL2, 120 Volt RSF2, RSF2 LED Polycarbonate
Optical Assembly: Opal Lens - made of UV stabilized injection molded polycarbonate.
12 Volt Lamping: 18W maximum S-8 (1141) lamp. Lamp is included with fixture.
120 Volt Lamping: 18W CFL (G24Q-2). 9W PLS Fluorescent (G23). 13W PLC
Fluorescent (120V: GX23-2; 277V: G24Q-1). 40W maximum T10 (4KV medium base porcelain
socket). Two 18W maximum S-8 (1141) lamps (Single contact bayonet base). Lower
wattage lamps are acceptable.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at
50,000 hours. Cool white (5500K nominal). Also available with warm lens.
LED Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature. Pre-wired with high
temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency:
60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts
(3) 1W LEDs, 13.5 total watts (5) 1W LEDs. |
|
| |
Hadco Low Voltage Louver BrickLytes
Housing: Aluminum parts have zinc-rich primer
and thermoset powdercoat for durability.
Faceplates are color-impregnated. Die-cast
aluminum back box contains less than 0.3%
copper to prevent corrosion in concrete or
masonry applications. Die-cast aluminum trim
contains less than 0.3% copper to resist
corrosion. (Note: Flange not included with
CB100 fixture.). Thermal Protection device
is required for installations in drywall,
plaster, wood or other non-masonry materials.
Finish: Thermoset polyester powdercoat is
electrostatically applied after a five-stage
conversion cleaning process and bonded by
heat fusion thermosetting. Zinc-rich primer
and thermoset powdercoat for durability.
Optical Assembly: The
cast louver offers lower light levels with
cut-off for lighting stairways or general
lighting where shielding of the light source
is more important than high light levels.
Symmetric reflector is precision formed,
steel with a white reflective coating. Horizontal
louver lens made of die-cast copper-free
aluminum with a 45° cutoff and frosted tempered
glass. Cast bronze louver is natural cast
bronze with frosted tempered glass.
WARRANTY: Three-year limited warranty.
CERTIFICATIONS: ETL listed to U.S. safety
standards for wet locations. cETL listed
to Canadian safety standards for wet locations.
Manufactured to ISO 9001:2008 Standards.
ADA Compliant when used in indoor and outdoor
wall applications.
Hadco
BrickLytes (Brick Lights) > |
 |
12
Volt RSCL2, 120 Volt RSC2 Aluminum
Finish:
A Black, B White, H Bronze
12
Volt Lamping: Two 18W maximum S-8 (1141) lamps
(Single contact bayonet base). Lamp is included
with fixture.
120 Volt Lamping: 9W PLS Fluorescent (G23). 13W PLC Fluorescent (120V: GX23-2; 277V: G24Q-1). 18W CFL (G24Q-2). Two 18W maximum S-8 (1141) lamps (Single contact bayonet base). 40W maximum T10 (4KV medium base porcelain socket). Lower wattage lamps are acceptable.
12
Volt
Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is pre-wired
with 6-ft. Pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick connector,
catalog #LVC3 included for easy hook-up to the low voltage supply cable, not
included. 12 Volt system requires remote transformer, not included.
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG black, white,
and ground wires. 1141 lamps use an integral 120V/12V transformer.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance
at 50,000 hours. Cool white (5500K nominal). LED Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature. Pre-wired with high
temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency:
60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts
(3) 1W LEDs, 13.5 total watts (5) 1W LEDs. |
 |
12
Volt RSCL2, 120 Volt RSC2
Natural Brass
Finish: N Natural Brass
Natural Brass louver is Natural Brass
with frosted tempered glass.
120 Volt Lamping: 9W PLS Fluorescent (G23). 13W PLC Fluorescent (120V: GX23-2;
277V: G24Q-1). 18W CFL (G24Q-2). Two 18W maximum S-8 (1141) lamps (Single contact
bayonet base). 40W maximum T10 (4KV medium base porcelain socket). Lower wattage
lamps are acceptable.
12 Volt Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is
pre-wired with 6-ft. Pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick
connector, catalog #LVC3 included for easy hook-up to the low voltage supply
cable, not included. 12 Volt system requires remote transformer, not included.
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG black, white,
and ground wires. 1141 lamps use an integral 120V/12V transformer.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at
50,000 hours. Cool white (5500K nominal). LED Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature. Pre-wired with high
temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency:
60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts
(3) 1W LEDs, 13.5 total watts (5) 1W LEDs. |
  |
12
Volt RSVL2, 120 Volt RSV2 Aluminum
Finish: A Black, B White, H Bronze
120 Volt Lamping: 9W PLS Fluorescent (G23). 13W PLC Fluorescent (120V: GX23-2;
277V: G24Q-1). 18W CFL (G24Q-2). Two 18W maximum S-8 (1141) lamps (Single contact
bayonet base). 40W maximum T10 (4KV medium base porcelain socket). Lower wattage
lamps are acceptable.
12 Volt Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is
pre-wired with 6-ft. Pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick
connector, catalog #LVC3 included for easy hook-up to the low voltage supply
cable, not included. 12 Volt system requires remote transformer, not included.
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG black, white,
and ground wires. 1141 lamps use an integral 120V/12V transformer.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at
50,000 hours. Cool white (5500K nominal). LED Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature. Pre-wired with high
temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency:
60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts
(3) 1W LEDs, 13.5 total watts (5) 1W LEDs. |
 |
12 Volt RSVL2, 120 Volt RSV2 Natural
Brass
Finish: N Natural Brass
Natural Brass louver is Natural Brass with frosted tempered glass.
120 Volt Lamping: 9W PLS Fluorescent (G23). 13W PLC Fluorescent (120V: GX23-2;
277V: G24Q-1). 18W CFL (G24Q-2). Two 18W maximum S-8 (1141) lamps (Single contact
bayonet base). 40W maximum T10 (4KV medium base porcelain socket). Lower wattage
lamps are acceptable.
12 Volt Electrical Assembly: Single contact bayonet (S-8). 12 volt fixture is
pre-wired with 6-ft. Pigtail of 18-2 AWG, 105° C, SPT-1W wire. Low voltage quick
connector, catalog #LVC3 included for easy hook-up to the low voltage supply
cable, not included. 12 Volt system requires remote transformer, not included.
120 Volt Electrical Assembly: Fixture is pre-wired with 18 AWG black, white,
and ground wires. 1141 lamps use an integral 120V/12V transformer.
LED Lamping: White high brightness (HB) LEDs. Deliver 70% lumen maintenance at
50,000 hours. Cool white (5500K nominal). LED Electrical Assembly: Powered by Advance™: Integral Advance™ electronic LED driver. UL class2. -40°C/F minimum starting temperature. Pre-wired with high
temperature 18 AWG wire. Input voltage range (VAC): 108-132. Input frequency:
60Hz. Integral surge protector built into LED driver circuit. 10.4 totals watts
(3) 1W LEDs, 13.5 total watts (5) 1W LEDs. |
|
Kichler Deck LED 2W Louver Face
Brick Landscape Light 15773AZT
|
Kichler Deck LED 3.8W Louver Face Brick
Landscape Light 15773AZT
15773AZT Textured Architectural Bronze $162.00
Contact Brand Lighting 800-585-1285 for Shipping & Discounts
Designed to be integrated into
a brick wall during construction. LED version
is also usable in vertical risers. Casts
a low, even spread of energy efficient LED light.
No remote driver required to operate these LED fixtures
Finish: Textured Architectural Bronze
Height 4" x Length 4" x Width
9.5"
Housing: Die cast aluminum with a fully
sealed heat-resistant glass lens
Wiring: Wire connection must be made inside
junction box.
Light Source: Illumination provided by integrated
3.8-Watt LED chips
Voltage: 12
Diffuser Description: Tempered Soda Lime
Glass, Frosted on one side
Body Material: Aluminum
UL CSA Listed
Kichler LED Lights > |
Kichler Deck LED 2W Glass Lens
Brick Landscape Light 15774AZT
|
Kichler
Deck LED 2W Glass Lens Brick Landscape Light
15774AZT
15774AZT Textured Architectural Bronze $158.00
Contact Brand Lighting 800-585-1285 for Shipping & Discounts
Designed to be integrated into
a brick wall during construction. LED version
is also usable in vertical risers. Casts
a low, even spread of energy efficient LED light.
No remote driver required to operate these LED fixtures
Finish: Textured Architectural Bronze
Height 4" x Length 3.76" x Width
9.5"
Housing: Die cast aluminum with a fully
sealed heat-resistant glass lens
Wiring: Wire connection must be made inside
junction box.
Light Source: Illumination provided by integrated
3.2-Watt LED chips
Voltage: 12
Diffuser Description: Tempered Soda Lime
Glass, Frosted on one side
Body Material: Aluminum
UL CSA Listed
Kichler LED Lights > |
|
|
Dabmar
LV-LED60 Recessed Brick, Step and Wall
Light
An excellent durable choice for commercial
or residential lighting.
Housing Material: Powder Coated Cast Aluminum
Available Finish: Stainless Steel
Cover Material: Stainless Steel
Lens: Crystal Lens
Pre-Wired with UL Listed Direct Burial Wire/Cable
ETL Approval Pending
Dimensions: 3.25"
Outside Dimension 5.5" x 5.5"
Depth 7/8"
| LV-LED60/B |
25 LEDs |
3W |
Blue |
12V |
Lamp Included |
| LV-LED60/G |
25 LEDs |
3W |
Green |
12V |
Lamp Included |
| LV-LED60/R |
25 LEDs |
3W |
Red |
12V |
Lamp Included |
| LV-LED60/W |
25 LEDs |
3W |
White |
12V |
Lamp Included |
|
|
|
Dabmar
LV-LED55 In-Ground Drive-Over Brick Light
An excellent durable choice for commercial
or residential lighting.
Material: Rated Drive-Over Glass
Lamp: LED 4W 12V Multi-Color included
Pre-Wired with UL Listed Direct Burial Wire/Cable
ETL Approval Pending
Dimensions: Top 3 5/8"
Outside Dimension 4" x 4"
Height 2 3/8"
Socket 1 1/2"
LVT25 - Transformer with Controller Required,
Sold Separately |
|
